Problem2:. Consider the circuits shown below. (a) Write the equation for current using the junction rule. (b) Write two equations using loop rule (c) Use these equations to find I₁, I2, and 13? (b) What is the power dissipated across each resistor (I²R)? V₁ = 24 V 12 R₂=652 R₁ = 802 ¹2 13 R3=452 W =₂=10 V

Problem2:. Consider the circuits shown below. (a) Write the equation for current using the junction rule. (b) Write two equations using loop rule (c) Use these equations to find I₁, I2, and 13? (b) What is the power dissipated across each resistor (I²R)? V₁ = 24 V 12 R₂=652 R₁ = 802 ¹2 13 R3=452 W =₂=10 V

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 74AP: Consider a circuit that consists of a real battery with an emf and an internal resistance of r...

See similar textbooks

Similar questions

(a) Explain how the mnemonic ELI the ICE man can be used to recall whether current leads voltage or voltage leads current in RLC circuits. Note that E represents emf . (b) Explain how CIVIL works as another mnemonic device, where V represents voltage.
In this chapter, most examples and problems involved direct current (DC). DC circuits have the current flowing in one direction, from positive to negative. When the current was changing, it was changed linearly from I=ImaxtoI=+Imax and the voltage changed linearly from V=Vmax to V=+Vmax where Vmax=ImaxR .Suppose a voltage source is placed in series with a resistor of R = 10 that supplied a current that alternated as a sine wave, for example, I(t)=(3.00A)sin(24.00st) . (a) What would a graph of the voltage drop across the resistor V(t) versus time look like? (b) What would a plot of V(t) versus I(t) for one period look like? (Hint: If you are not sure, try plotting V(t) versus I(t) using a spreadsheet.)
Ralph has three resistors, R1, R2, and R3, connected in series. When connected to an ideal emf source E1, current I1 flows through the resistors. a. If the resistors are instead connected to a second source with E2=2E1, what is the new current through the resistors in terms of the first current? b. Show that, if each resistance is doubled and the resistors are connected in series to the second emf source, the current through the resistors is equal to I1.
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
Consider a resistor made from a hollow cylinder of carbon as shown below. The inner radius of the cylinder is Ri= 0.20 mm and the outer radius is R0 = 0.30 mm. The length of the resistor is L = 0.90 mm. The resistivity of the carbon is =3.5105 m. (a) Prove that theresistance perpendicular from the axis is R=2L1n(R0Ri) . (b) What is the resistance?
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
The power dissipated in a resistor is given by P=V2/R, which means power decreases if resistance increases. Yet this power is also given by P=I2/R , which means power increases if resistance increases. Explain why there is no contradiction here.
The figure shows a resistor of resistance R = 6.32 connected to an ideal battery of emf 8 = 14.0 V by means of two copper wires. Each wire has length 22.0 cm and radius 2.30 mm. In dealing with such circuits in this chapter, we generally neglect the potential differences along the wires and the transfer of energy to thermal energy in them. Check the validity of this neglect for the circuit of the figure below. What is the potential difference across (a) the resistor and (b) each of the two sections of wire? At what rate is energy lost to thermal energy in (c) the resistor and (d) each section of wire?
What voltage will produce 0.2 AA of current through a 4800-ΩΩ resistor? Express your answer to two significant figures and include the appropriate units. V=
To get the minimum current, the connection should be in series. If you create a series connection with 30V DC source and three resistors with R1 = 50Ω, R2 = 75Ω, and R3 = 100Ω, how do you calculate for the total current (IT) and the current flowing in each resistor (I1, I2, I3), and the total voltage (VT) and the voltage across each resistor (V1, V2, V3)? How do you also determine the power dissipated by each resistor (P1, P2, P3) and by the whole circuit (PT)??
Consider a series RC circuit as in the figure below for which R = 8.00 MΩ, C = 3.00 µF, and = 34.0 V. What is the time constant of the circuit. What is the maximum charge on the capacitor after the switch is thrown closed? Find the current in the resistor 10.0 s after the switch is closed.
An R=88MS resistor and a C =43. capacitor are connected in series with a open switch and an V = 45.4V potential source. The capacitor is initially uncharged. The switch is closed at t = 0. Determine the current in the circuit when the charge on the capacitor is 1/9 of its maximum value (in p.A). I need to look. At correct answer and show all work please