i need the answer quickly Procedure:1- Determine the value of Rsh which is required to be connected with themoving coil to obtain 60µA , 90 µa, 120 µa full scale deflection assumingRm = 1KN, Im = 30 µa2- Connect the circuit shown and record the reading of the ammeter .Discussion:1.Find the current math mathematically.2. Conclusion

Answered: Image /qna-images/answer/313cab74-b806-4797-a3c1-dc40eb35a25f.jpg

Procedure: 1- Determine the value of Rsh which is required to be connected with the moving coil to obtain 60µA , 90 µa, 120 µa full scale deflection assuming Rm = 1K2, Im = 30 µa 2- Connect the circuit shown and record the reading of the ammeter . Discussion: 1.Find the current math mathematically. 2. Conclusion

Procedure: 1- Determine the value of Rsh which is required to be connected with the moving coil to obtain 60µA , 90 µa, 120 µa full scale deflection assuming Rm = 1K2, Im = 30 µa 2- Connect the circuit shown and record the reading of the ammeter . Discussion: 1.Find the current math mathematically. 2. Conclusion

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
Determine 1) the maximum load current. 2) the mean load current .3)the rms alternating load current. 4) the DC power supplied to the load. 5) the input power to the anode circuit. 6) the rectification efficiency. 7) the percentage of regulation. 8) the ripple current. R=10°0 Vi R=10°n AC Figure (2-72) the circuit of problem (2-6). (2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of Ikn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode. (2-8) A zener diode has a de power dissipation of Iw and a zener voltage rating of 27v. What is the value of I, max for the device? (2-9) Calculate and draw the output voltage for the circuit shown in Figure (2-74). +100v Vo 2.2kd4 2.2kQ -100v Figure (2-74) the circuit of problem (2-10).
Fundamentals of Electric Circuits
iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. ,Da 5:1 120 V ms RL=10k2 R1 ell lelll
multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -
31. If the voltage measuring function of a linear NTC thermistor is Vout = -1.4T( "C) + 4.35 V, the slope of the corresponding display function for measured temperature is (a) 1.400 °C/V (b) -0.7143 "C/v (c) -1.235 "C/v
Question (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor (a) Determine the delay angle such that the average load current is 2.5A (b) Determine the power absorbed by the load (c) Determine the power factor.
AN Sesli oku 1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm32k İm-(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances) ult) R2 本 R3 20k 18k R4 k: k2 10k
An alternating current was measured by a DC milliammeter in conjunction with afull-wave rectifier. The reading on the milliammeter was 7.0 mA. Assuming thewaveform of the alternating current to be sinusoidal, calculate: (a) the r.m.s. valueand (b) the maximum value for the alternating current.
aph R₁ 100 ΚΩ R₂ www R₁ 1.0 kn body 1. Determine the necessary value of R2 in Figure 4 so that the circuit will oscillate. Neglect the forward resistance of the Zener diodes. (Hint: The total gain of the circuit must be 3 when the Zener diodes are conducting.) 2. Explain the purpose of R₁ in Figure 4. www. body bold 6.8 V 6.8 V R3 47 ΚΩ R₁ www 1.0 kn 0.015 μF Normal 0.015 µF No Spacing Styles He
Q: - Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. 4:1 D, 120 V rms c) If sin wave with 100µf connected in parallel with the resistor, calculate the ripple сарacitor is 60 HZ 1.0 kN D2 factor lllee lelll
Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode