Properties of Carbon Dioxide: h @ 220 KPa and -5°C = 350 KJ/kg h.@ 25°C = 223.65 KJ/kg h.@ 22°C = 220.75 KJ/kg h. @ 220 KPa = 347.13 KJ/kg %3D Saturated Vapor Carbon Dioxide refrigerant at 220 KPa leaves the evaporator and enters the compressor at -5 °C. The refrigerant leaves the condenser as saturate liquid at 25 °C and enters the expansion valve at 22 °C. Heat rejected from the condenser amount 90 KW. The work to the compressor is 60 KJ/kg while the heat lost from the compressor is 5 KJ/kg. If 2.5 KJ/kg of heat are lost in the piping between the compressor and condenser. Solve for the mass flowrate of the refrigerant in kg/hr.

Properties of Carbon Dioxide: h @ 220 KPa and -5°C = 350 KJ/kg h.@ 25°C = 223.65 KJ/kg h.@ 22°C = 220.75 KJ/kg h. @ 220 KPa = 347.13 KJ/kg %3D Saturated Vapor Carbon Dioxide refrigerant at 220 KPa leaves the evaporator and enters the compressor at -5 °C. The refrigerant leaves the condenser as saturate liquid at 25 °C and enters the expansion valve at 22 °C. Heat rejected from the condenser amount 90 KW. The work to the compressor is 60 KJ/kg while the heat lost from the compressor is 5 KJ/kg. If 2.5 KJ/kg of heat are lost in the piping between the compressor and condenser. Solve for the mass flowrate of the refrigerant in kg/hr.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

34 - Helium enters a continuous flow compressor at 326 K and leaves at 441 K. If the mass flow rate is 1.5 kg/s, which of the following is the required power? (Cp = 5.1926 kJ/kgK) a) 988.7 kW B) 895.7 kW NS) 617.9 kW D) 927.9 kW TO) 836.0 kW
A certain Geothermal Power Plant shows that 1,700,000 kg/hr of pressurized ground water is available at 17.5MPa and 330°C. The water will be throttled to a pressure of 1.7MPa to produce wet steam and this mixture will be passed through a water separator to remove the water droplets so that saturated steam at 1.7MPa is available at the entrance of the Turbine. Other data are as follows: Discharge Pressure of turbine = 85kPa-Vac; Turbine Efficiency = 73%. Mechanical Loss = 2% of shaft power. Generator Efficiency = 95%. Determine the following: 1.The mass flow rate, in kg/min, of steam entering the turbine. a. 153,720 b . 76,858 c. 38,430 d. 19,200 e. 9,350 2. The maximum amount of power, in kW, that the plant can generate. a. 38,430 b. 19,200 c. 76,858 d. 9,350 e. 153,720
A car wash service uses 150 litre of pressurized (3 bar) warm water (45oC) to wash each car. It takes 10 min to wash each car. The service has 10 washing lanes, and it is open from (14:00 to 21:00) every day and 360 day per year. Each day 400 cars are washed. Fresh water at 1 bar pressure and 15oC is pressurized in a pump and then heated to desired temperature. Assume pump operates adiabatically and its efficiency is 85%, which is defined as the ideal power input divided by the actual power input. The ideal power input is the product of the volumetric flow rate times the pressure drop across the pump. All the other equipment of the car wash uses 5 kW of power during operation. Current (first alternative) is to buy electricity from the utility and use a natural gas fired boiler to heat the water. Assume natural gas furnace used in heating has 90% overall efficiency defined as heating provided water to heating released from fuel. The heating value of the natural gas (CH4) is 55.5 MJ/kg,…
Define the Reversible Isothermal Compression
A three-stage compressor receives 500 lps of air at 101 kPaa and 27 oC, anddischarges at 750 kPaa. Determine a) the power required; b) the pressure at eachintercooler; c) the maximum temperature; and d) the heat transferred in each intercooler.e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?(answers for Letter D and E Thank you)
Steam with h = 2442.6 kJ/kg flows at the rate of 22.7 kg/s into a water-steam condenser at the constant temperature of 48.9oC. The condensed steam leaves with h = 181.4 kJ/kg. The cooling water (cp = 4.187 kJ/kg-K) enters at 24.4oC and leaves at 37.8oC. Consider the condenser as an adiabatic steady flow system with ∆P = 0 and ∆K = 0. Compute the entropy production for the system; To = 21.1oC
Pls. answer thank you! The following performance data were generated by a gas turbine having intercooling: LP compressor inlet conditions of 14.7 psia and 520’’R: LP compressor isentropic discharge temperature, 743.8 R. compressor isentropic efficiency. 78 percent; HP.compressor inlet temperature, S20 degree R: HP compressor isentropic discharge temperature, 743.8 R. HP compressor isentropic efficiency, 82%; turbine inlet temperature, 2000R; and turbine isentropic efficiency, 90%, Calculate the net cycle work Btu/lb.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
Thermodynamics Determine the useful power produced in a thermally insulated turbine from 30 bar and 340Ç to 0.5 bar and 90% quality. The water flow is 15000kg/h
Is aircon-ditioner an example of thermodynamic system inside the house? Is it an open system, closed system or isolated system? Explain why.
An axial flow compressor having eight stages and with 50% reaction design compresses air in the pressure ratio of 4 : 1. The air enters the compressor at 20°C and flows through it with a constant speed of 90 m/s. The rotating blades of compressor rotate with a mean speed of 180 m/s. Isentropic efficiency of the compressor may be taken as 82%. Calculate : (i) Work done by the machine (ii) Blades angles. Assume γ = 1.4 and cp= 1.005 kJ/kg K.
The working substance for a carnot cycle is 8 lb of air. the volume at the beginning of isothermal expansion is 9 cubic feet and the pressure 300psia. the ratio of expansion during the addition of heat is 2 and the temperature of the cold body is 90 degree farenheit. Find (a) Qa,(b) Qb,(c) V3,(d) P3,(e) V4,(f) P4,(g) Pm, (h) the ratio of expansion during the isentropic process, and (i) the overall ratio of compression.