14. Provide a detailed step by step solution. Situation 13- A retaining wall 9 m in height is subjected to earth pressure that variesuniformly from 0 kN/m at the top to 52 kN/m at bottom. The wall is simplysupported at top and fixed at bottom.37. Compute the moment (kN-m) at fixed end.A. 421B. 281C. 365D. 254struction38. Compute the shear (kN) at fixed end if support at the top is removed.C. 325A. 234D. 124B. 28739. Compute the moment (kN-m) at fixed end if support at the top is removed.A. 548B. 763D. 702

Answered: Image /qna-images/answer/6d6e6cbc-b89f-433d-9c17-0029df3960d6.jpg

Answered: Provide

Engineering

Civil Engineering

Provide

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: . A square footing 2.5 m size is founded at a depth of 1.5 m in a sandy soil deposit which has the…

A: Given: Square footing with width = 2.5m. Depth of footing = 1.5m N= 30 FOS=3. Permissible…

Q: Problem 5. The frame shown is hinged to rigid supports at A and E. Find the components of the hinge…

Q: Q2 Rankine's lateral pressure distributions against the vertical wall are include the effect of a…

Q: Use AISC Equation E3-2 or E3-3 and determine the axial compressive strength oP for the following…

A: Consider the column as in the below diagram;

Q: For the truss shown below, P = 9.2 kips, a = 8 ft, and b = 6 ft. Determine the force in member 2…

A: The truss with loading is shown below.

Q: 1. Draw the shear and moment diagram for the frame shown. 4 m A 100 KN 1.5 m+1.5 m 12 kN/m 5 m- 1

Q: Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C…

A: The given figure can be considered as :

Q: question • Find the support Jeautions (for A and B) Neglect Beam weight D I got: RA= 12,50ON, RB =…

Q: Find a absolute axial Force at member AB and BD when the unit load is placed at B

A: Calculation of reactions when unit load is at B Since the loading is symmetrical we get equal…

Q: For a certain arrangement of two bars carrying only axial forces, the equilibrium and compatibility…

A: Given; The equilibrium and compatibility equations are: Equilibrium: t1+3t2=2kN Compatibility: 2e1 +…

Q: For the same intersection in Problem 2, left-turning vehicles in the north-bound approach must seek…

A: To determine if left-turning vehicles at the intersection have sufficient sight distance (ISD) to…

Q: A ball moving on a smooth horizontal table hits a rough vertical wall, the coefficient of…

A: Give data Ball is moving on the smooth surface. Assume initial velocity of ball = u And Hits to…

Q: The state of stress at a point is given by: o= 80 MPa, oy=100 MPa and tauxv =60 MPa. If the yield…

A: State of stresses-σx=80 MPaσy=100 MPaτxy=60 MPayield strength-fy=150 MPa

Q: 3 A triangular channel with apex angle 60° is carrying a uniform flow of 4.25 m/s with a depth of…

Q: a. Check the adequacy of the beam for flexure (2= 1.67) and shear (Cy= 1.0 and £2,= 1.5). b. Check…

Q: What is the probability of an equal to or greater than 25 years flood occurring twice in the next…

A: Given - Return Period (T) = 25 years Find out - Probability of occuring of flood twice in next…

Q: Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L…

A: Concrete shear reinforcement is designed to resist forces greater than concrete's shear strength. A…

Q: a. Determine the moment of inertia at the horizontal neutral axis. b. Determine the shear flow at…

A: To calculate the location of horizontal Neutral axis we have y = Ac*yc+Af*yfAc+Af Ac = area of…

Q: The load on each axle of a locomotive is 22 tonnes. If the coefficient of friction is 0.2, then the…

Q: A submerged clay layer has a thickness of 8m. the water content of the soil particles is 50%. The…

A: A submerged clay layer Thickness (Z) = 8m Water content (w) = 50% = 0.5 Specific gravity (G) =…

Q: A city supply of 15000 cubic metres of water per day is treated with a chlorine dosage of 0.5 ppm.…

Q: reinforced concrete column of cross-section (300x300) mm2 supports an axial dead load PG =800 kN and…

Q: An eight-lane freeway section is designed to have a lane width of 10 ft, right-side shoulder width…

A: Number of lanes = 8 Number of Lanes in each direction = 4 Width of lane = 10 ft Right side shoulder…

Q: Rainfall Depth and Intensity 2. Given the rainfall incremental depth compute the following; to =…

A: Given: Time is in minutes. Rainfall Incremental Depth is in mm. Assumption: Rainfall intensity…

Q: A 30 cm square plate settle by 8 mm in the plate load test on a cohesionless soil, when the…

A: A square bearing plate with, Width of plate, Bp=30 cm = 0.3 m Settlement of plate, Sp = 8 mm…

Q: 2 kip / ft 6 ft A O 6 ft 30 kip ft 6 ft B

Q: The upward flow of water through a layer of sand in the tank shown in figure has the following…

A: e = 0.50 G = 2.67 To find: 1. Effective stress at point A. 2. Effective stress at point B. 3. Upward…

Q: 2. Determine if the composite beam pictured below is adequate for this application (this includes…

A: For W24 x 94 composite beam given: Thickness of all members = 4in Span Length = 30' , Service Live…

Q: A circular surface area 200 cm² is inclined to the x and y axes such that the unit vector normal to…

Q: A two lane single carriage-way is to be designed for a design life period of 15 years. Total two way…

A: →Design life period n=15 years→Traffic intensity A=2000 vec/day→vehicle damage factorf=3→lane…

Q: An eight-lane freeway section is designed to have a lane width of 12 ft, right-side shoulder width…

A: Given; Lane width = 12 ft. Right-side shoulder width = 3 ft. and 3 ramps over a 2- mile- long…

Q: Draw the V&M diagrams and calculate the largest permissible value of P for the beam and loading…

A: Allowable normal stress in tension=-80MPa Allowable normal stress in Compression=-140MPa To find…

Q: If the average daily consumption of a city is 100,000 m³, the maximum daily consumption on peak…

A: Given data: The average daily consumption = 100,000 m3 Peak hourly demand =? We have to calculate…

Q: Use the virtual work method to determine the horizontal deflection at joint C (Ac-x) of the frame…

A: Given data:

Q: Water flows at 150 ft³/s down a rectangular channel made of finished concrete. The channel has a…

A: Water flow=150ft3/sec Channel width=10ft Downward slope = 0.0002 manning's constant n=0.0012 Water…

Q: A discharge of 0.6 m³/s flows through a horizontal bend as shown in figure. Calculate the force on…

A: Given; Discharge (Q) = 0.6 m3/s Dia. at section 1 = 15 cm = 0.15 m Dia. at section 2 = 5 cm = 0.05 m…

Q: H.W3 Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I =…

Q: The average daily traffic on a stretch of road is 300 commercial vehicles per lane per day. Design…

A: Average daily traffic ADF=300 vehicles per lane per day. Time durations n=10 years. Vehicle damage…

Q: The absolute maximum Bending Moment in a simply supported beam of span 20 m due to a moving udl of 4…

A: Simply supported beam of 20m span length Moving udl of 4t/m span over 5m To find Absolute maximum…

Q: An axial centric force of magnitude P = 450 kN is applied to the composite block shown by means of a…

Q: A grass-lined trapezoidal channel has a bottom width of 40.0 ft with 4H:1V side slopes. The channel…

A: The given grass lined trapezoidal channel has a width is, 40 ft The given side slope is, below…

Q: Areal Precipitation 4. Determine the areal rainfall of the given drainage basin below using: a.…

A: A drainage basin as shown- Rain gauge readings given as- PA =30 mm, PB =40 mm, PC =10 mm, & PD…

Q: 3. A thin rod is free to rotate without friction about a fixed axis at Point A. The other end (Point…

A: The angle of the cable attached at point B = 45° The mass of the thin rod = 18 kg The length of the…

Q: The sequent depths in a hydraulic jump formed in a 4.0m wide rectangular channel are 0.3 m and 1.2…

A: Given- Sequent depths- y1=0.3 m,y2=1.2 m, Width of channel b = 4 m, It is needed to find the…

Q: The hydraulic head that wou quick condition in a sand str 2.3 m, specific gravity 2.67 c 0.67 is…

Q: 7. Draw the influence lines for the shear reactions at the internal hinges at points B and F, the…

Q: Terminal Velocity 3. Given: Atmospheric pressure = 101.3 KPA Air density = 1.20 kg/cubic meter Size…

A: Atmospheric pressure =101.3kpA , Air Density = 1.20kg/cubic meter Size of rain droplet = 0.6mm ,…

Q: The cross section of a gravity dam is given below. The normal operating level of the reservoir is 50…

A: Given; Normal operating level of the reservoir = 50 m The maximum level = 55 m The friction…

Q: Q1 A survey conducted to determine the choice of transportation mode (public bus or private car)…

A: Utility function equation Um = Bm - 0.45C - 0.25T

Q: consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips…

A: To find- What is the shear force in the bottom beams (absolute value)? What is the shear force in…

Question

14. Provide a detailed step by step solution.

Situation 13- A retaining wall 9 m in height is subjected to earth pressure that varies
uniformly from 0 kN/m at the top to 52 kN/m at bottom. The wall is simply
supported at top and fixed at bottom.
37. Compute the moment (kN-m) at fixed end.
A. 421
B. 281
C. 365
D. 254
struction
38. Compute the shear (kN) at fixed end if support at the top is removed.
C. 325
A. 234
D. 124
B. 287
39. Compute the moment (kN-m) at fixed end if support at the top is removed.
A. 548
B. 763
D. 702

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: GIVEN DATA

VIEW

Step 2: SOLUTION

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the magnitude of the projected component of the force F = {400i - 200j + 500k} N acting along the cable BA.
Compute the horizontal reaction at A of the arch in Figure P6.26.
A smooth backed vertical wall is 6.3m high and retains a soil with a bulk unit weight of 18 KN/m^3 and angle of friction 18 degrees. The top of the soil is level with the top of the wall and is horizontal. If the soil surface carries a uniformly distributed load (surcharge) of 4.5 KN/m^2, what is the difference in active moment at the base of the wall with surcharge and without surcharge.
The retaining wall shown has a height of 6m with its ground watertable located at a depth of 2m below the ground surface. There is a surcharge of 15kN/m^2 at the top. Compute the Rankine active force on the wall per unit. Compute the location of this force from the bottom of the wall. Compute the moment due to this force.
A 9 m cantilever retaining wall is subjected to active pressure increasing from 5 kN/m at the top (free end) to 45 kN/m at the base (fixed end) per meter strip of length of wall along its longitudinal axis. 4. Calculate the maximum shear in kN. Calculate the maximum moment. If the wall was laterally supported at the free end, determine the moment (kN∙m) at the base.
The cable in Figure P6.3 supports girder DE uni- formly loaded with 4 kips/ft. The supporting hangers are closely spaced, generating a smooth curved cable. Determine the support reactions at A and C. If the maxi- mum tensile force in the cable cannot exceed 600 kips, determine the sag hB at midspan.
A 6 m. cantilever retaining wall, supports an active pressure which varies from zero at the top to 35 kN/m at the bottom. Assume EI is constant. 1. Compute the maximum moment. 2. If the wall is fixed at the free end, determine the moment at the foundation. Use end moment equations wL^2/30 at the top and wL^2/20 at the base.
A vertical wall with a smooth face is 7.20m high and retains soil with an angle of friction of 27°. Unit weight of soil is 20KN/m³. Determine the total active force if the wall retains a sloping backfill which makes an angle of 9° with the horizontal.
Determine the tension P in the cable which will give the 100 lb-block a steady acceleration of 5 ft/sec^2 up the incline.
The arch shown in Figure P6.21 has a pin sup- port at A and a roller at C. A tension rod connects A and C. Determine the reactions at A and C and the tension in rod AC.
The cable shown carries weights (W1 = 16 kN, W2 = 22 kN) at points C and D. Determine the value of the REACTION (kN) at D. Use x1 = 4 m., x2 = 10 m., x3 = 6 m., y = 5 m., θ = 39°.
A two hinged parabolic arch of span 30m and rise 6m carries a uniformly distributed load of 20kN/mcovering a distance of 12m from left end. Find the horizontal thrust and the reactions at the twosupports. Also calculate the maximum hogging moment in the arch.