A motor is driving an output shaft through a single-stage gears, as shown.Input Gear, N,MotorToOutput Gear, N2Number of teeth of the input gear, N1 = 24;Number of teeth of the output gear, N2 = 48;Gear efficiency = 95%;%3!If the output shaft is to deliver torque To = 20 Nm, calculate the torque required on the input shaft, Ti. Give your answer in Nm to 1decimal places.

Net torque acting on the system will be zero so the sum of all the torque should be equal to zero.…

Answered: ptor is driving án output shäft through…

Engineering

Mechanical Engineering

ptor is driving án output shäft through å šinglê-štagê gears, as šh Input Gear, N1 Motor 'Ti To OUutput Gear, N,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
I n a reverted gear train, as shown in Fig. Q2, two shafts A and B are in the same straight line andare geared together through an intermediate parallel shaft C. The gears connecting the shafts Aand C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm.The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio ateach reduction is same. Find suitable number of teeth for all gears. The number of teeth of eachgear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance ofshaft C from A and B
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
Q.8 A pair of helical gears in which teeth on pinion are 20 and on gear are 30, the normal module is 5 mm and normal pressure angle is 20°. The helix angle is 30°. The pinion is provided 5 kW at 720 rpm. Determine various forces on the teeth.
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
A spur gear wheel will be produced for the motion mechanism of a woodworking machine driven by a single cylinder engine. Considering the data below, find the tangential force on the gear in Newtons according to the root strength. Module for gear=5 cm ; module width ratio =14 ; number of teeth=16 ; Clutch ratio=1 ; form factor Kf=1.4 ; load distribution factor Km=1.5 ; the circumferential speed of the gear is =56 m/sec (To be used only in Kv calculation). Safety stress of gear material=37 N/mm2. 1-) Table will NOT be used for Kv-Speed factor. It will be calculated with the formula Kv=1+0.03*V. 2-) V in Kv calculation shows the velocity as m/sec. 3-) It will be taken as Pi=3.14.
Explain properly 1: What are the stresses which are applied on helical and spur gears? and What are the important considerations which should be considered in designing helical and spur gears?
Examine the diagram of a gear set. What is the Diametral Pitch of these gears? What is the Gear Ratio? What will be the output torque of the Driven Gear? What will be the output speed of the Driven Gear?
A spur gear wheel will be produced for the movement mechanism driven by the electric motor of a crane system. Calculate the modulus in millimeters according to the root strength, taking into account the following data. Module width ratio =10, number of teeth=18, Clutch ratio(not clutch factor)= 1.5 , form factor Kf=1, operating factor Ki=1, load distribution factor Km=1, speed factor Kv=1, Driving electric motor Its power is P=1917 kW and the speed of the gear is n=48 rpm. Safety stress of gear material=322 N/mm2.
Design A two stage spur gear reduction unit with 20- Deg full depth involute teeth. The input shaft rotates at 1440 rpm and receives 10 kW power. The speed of the output shaft should be approximately 180 rpm plus minus 5 rpm , All gears are made of steel and have the same module . Determine appropriate number of teeth of the gears in the unit .
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion. If the pinion has 20 teeth, use the Lewis formula to determine the face width of thepinion and gear. Then, do one set of calculations and tabulate the answers.