The gearing of a machine tool is shown in Fig. 9.22. The motor shaft is con- nected to A and rotates at 975 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft G. What is the speed of F? The number of teeth on each wheel are as given below:

The gearing of a machine tool is shown in Fig. 9.22. The motor shaft is con- nected to A and rotates at 975 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft G. What is the speed of F? The number of teeth on each wheel are as given below:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I n a reverted gear train, as shown in Fig. Q2, two shafts A and B are in the same straight line andare geared together through an intermediate parallel shaft C. The gears connecting the shafts Aand C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm.The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio ateach reduction is same. Find suitable number of teeth for all gears. The number of teeth of eachgear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance ofshaft C from A and B
The axes of two parallel shafts are to be 600mm apart approximately, and have to be connected by spur gear, having a circular pitch of 30 mm. If gear A rotate at 200 rpm and gear B rotate at 600 rpm, find the number of teeth on each gear.
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 35cm respectively. If driven shaft runs with 8 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 5mm
The four rigid gears, loadedas shown in Fig. (a), areattached to a 1.5-in.-diametersteel shaft. Compute theangleθ of rotation of gearA relative to gearD. UseG=12×106 psi for the shaft
Please solve in 30 min The teeth number of each gear is already given (e.g. Z₁ =14). If the rotation speed of gear 1 is n₁=380 r/min, calculate the rotation speed of gear carrier H
The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction. Gears B and C are compound gears as well as gears D and E. Gear A meshes with gear B and gear C drives gear D. Gear E meshes with gear F which is mounted on the driven shaft. The number of teeth on gears A, B, C, D, E and F are 21, 35, 49, 63, 56 & 84 respectively. Sketch the arrangement and determine the speed (rpm) and direction of gear F? Calculate the centre distance between the driver and driven shafts if the module of gears is 2.3 mm
There are three parallel shafts 1, 2 and 3. Gear A on shaft 1has 28 teeth of diametral pitch of 4 meshing with a larger gear B in shaft 2 having 70 teeth. A smaller gear C having 24 teeth on shaft 2 and diametral pitch of 5.2 meshes with a 50 teeth gear D of shaft 3. Determine the rpm of shaft 2 if shaft 1 turns 1,744 rpm.
Two parallel shaft connected by spur gears turn in the same direction and having a speedratio of SR = 4.72 (a) What is the distance of the two shaft, in mm, if the smaller gear is170 mm in diameter? (b) What is the diameter of the larger gear in mm?
lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle. Determine the velocity ratio and the pitch angles. of both gears.
In an epicyclical gear train of the sun and planet, the pitch circle diameter of the internally toothed ring is to be 224mm and the module 4mm. when the ring D is stationary, the spider, which carries three plant wheels C of equal size, is to make one revolution in the same sense as the wheel For every five revolutions of the driving spindle carrying the sun wheel B. Determine suitable numbers of teeth for all wheel.
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 1000 r.p.m. and the other at 2500 r.p.m., find the number of teeth on each wheel, if the module is 9 mm. Also determine the exact distance apart of the shafts.