pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 75 L/min to a tank 3.5m above the pump. The pressure at A is -20 kPa and the pressure at B is 275 kPa. The head loss in the system is 2.5 times the velocity head in the discharge pipe. Calculate the power (kW) delivered by the pump for pipe diameter at suction in 52.54mm and discharge pipe diameter is 26.64mm. The

pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 75 L/min to a tank 3.5m above the pump. The pressure at A is -20 kPa and the pressure at B is 275 kPa. The head loss in the system is 2.5 times the velocity head in the discharge pipe. Calculate the power (kW) delivered by the pump for pipe diameter at suction in 52.54mm and discharge pipe diameter is 26.64mm. The

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity of the liquid flowing through the rusty iron pipe having a 150 mm diameter is 2.5 m/s. The pressure head at section A is 37 m, while at section B, which is 30 m far from A, the pressure head is 32 m. Compute the head loss between A and B. Calculate the flow rate in the system in L/hr. Determine the value of the friction factor “f”.
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The sucLon pipe is 350mm in diameter and 12m in length and the delivery pipe is 550mm in diameter and 40m in length. Calculate:(a) The maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (b) the energy to be supplied by the pump per unit mass of water transferred (c) The input power required by the pump, which is 60 % efficient
Water recirculates at a volume flow rate of 0.4524 ft3/min from the blade outlet to the impeller, and shaft sealing losses are negligible. A centrifugal pump has a hydraulic efficiency of 95% and a mechanical efficiency of 93%, respectively. Calculate the pump efficiency in percent if the pump delivers water at a flow rate of 12 ft3/min.
A pelton type turbine has installed 37 m below the head gate of the penstock. The head loss due to friction is 26 % of the given elevation. Determine the total head in meters.
Two reservoirs with top surfaces placed on the flat ground and connected with each other with a straight pipe and pump system. The height of the first reservoir is Z1=10 m and the second reservoir is Z2=30 m from the ground level. The pump sucks water from the first reservoir and conveys into the second reservoir. The major head loss along the pipe is hf=40 m with ignoring local head losses. Calculate the manometric head of the pump in a meter of water.
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A
Water is pumped through a 750ft long inch nominal diameter sch 40 pipe. The difference in height between the outlet and inlet planes is given as 50 ft. Pump efficiency is 80% and the power of the motor is 20 horsepower. Friction losses are given as 50 ft-lbt / lbm. Calculate the flow rate in the pipeline.
A storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is 500liters per second the head loss in the 300 mm pipe supplying the turbine is 2.5 m. Determine the pressure at the entrance of the turbine. If a negative pressure of 30 kPa exists at the 600 mm diametersection of the draft tube (exit tube) below the turbine 1.5 m below the supply line, estimate the energy absorbed by the turbine in kW neglecting losses between the entrance and exit of the pipe. Findalso the output of the turbine assuming an efficiency of 85%. *can you also provide its figure, Thank you.
A fluid is flowing in a horizontal pipe 8 in. in diameter with a mean velocity of10 ft/s. The pressure at the center of the pipe is 5 psi, and the elevation of thepipe above the assumed datum is 15 ft. Compute the total head in feet if the fluid is (a) water, (b) oil (SG=0.8), and (c) molasses (SG=1.5).
The volumetric flow of water is 665.98 liters/min. Calculate the maximum length [m] of the pipe that can be used without cavitation? (NOTE: Take the water temperature 10 °C)
A storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is 500 liters per second the head loss in the 300 mm pipe supplying the turbine is 2.5 m. Determine the pressure at the entrance of the turbine. If a negative pressure of 30 kPa exists at the 600 mm diameter section of the draft tube (exit tube) below the turbine 1.5 m below the supply line, estimate the energy absorbed by the turbine in kW neglecting losses between the entrance and exit of the pipe. Find also the output of the turbine assuming an efficiency of 85%
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.