please solve it quickly, thanks ❤️ Q: A composite section shown in Figure consisted of a rectangular and triangular sections with asemicircle hole as shown. Locate the centroid (x, y) of each this section using the below table.Y90 mm60 mm60 mm10 mm5 mm8 mm20 mm30 mm20 mm10 mm5 mm8 mm60 mm30 mm45 mmXFigure 1Figure 2Figure 3X;PartArea A, (mm?)A, X, (mm')A, Y (mm')(mm)(mm)+Yellow rectangle+ Blue triangleWhite semicircleTotals

Consider the free body diagram as;

Q: A composite section shown in Figure consisted of a rectangular and triangular sections with a semicircle hole as shown. Locate the centroid (x, y) of each this section using the below table. 90 mm 60 mm 60 mm 10 mm 5 mm 8 mm 20 mm 30 mm 20 mm 10 mm 8 mm 5 mm O mm 45 mm 30 mm Figure 1 Figure 2 Figure 3 X, Y Part Area A, (mm') A, X; (mm') A, Y (mm') (mm) (mm) +Yellow rectangle + Blue triangle - White semicircle Totals

Q: A composite section shown in Figure consisted of a rectangular and triangular sections with a semicircle hole as shown. Locate the centroid (x, y) of each this section using the below table. 90 mm 60 mm 60 mm 10 mm 5 mm 8 mm 20 mm 30 mm 20 mm 10 mm 8 mm 5 mm O mm 45 mm 30 mm Figure 1 Figure 2 Figure 3 X, Y Part Area A, (mm') A, X; (mm') A, Y (mm') (mm) (mm) +Yellow rectangle + Blue triangle - White semicircle Totals

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.13P

See similar textbooks

Similar questions

A built-up section is used as a structural member for a two-storey structure. Two channels and angle bars are to be welded to a rolled W section as shown. Determine the following if every section have dimensions in inches equal to : a= 11.10, b= 3.05, c= 0.50, d=3 , e=1/2, f=18.60, g=11.10, h= 0.535, i= 0.87 * Compute the section modulus of the composite section: Use S= Ix/ c, where Ix = moment of inertia of built up section, c= distance from neutral axis to the topmost/ bottommost fiber of the built up section. Compute the radius of gyration with respect to the x-axis Centroidal moment of inertia with respect to the y-axis. Centroidal moment of inertia with respect to the x-axis. Compute the radius of gyration with respect to the y-axis pls help me solve this (T___T) P.S : 3 decimal places
The composite section shown in the figure is made up of C 15 x 40 and S 24 x 121. Determine the properties of composite section. a.Ix, Sx and rxb.Iy, Sy, and ry
The composite A-36 steel bar shown is made from two segments, AB and BD, having cross-sectional areas of AB = 641 mm2 and BD = 1202 mm2 . Determine the vertical displacement (in mm) of end A. Modulus of Elasticity = 210 GPa. X = 1016 mm, Y = 790 mm, Z = 526 mm. Input the magnitude only. The answer is 0.58185. Show solution pls. Thank you.
Determine the x-bar centroid of the composite figure shown X1=71 X2=105 Y= 76
Determine the moment of inertia (mm4) Īy of the area shown with respect to the vertical line that passes to the centroid of the composite area if a = 37 mm, b = 76 mm, and h = 148 mm. Round off only on the final answer expressed in whole number.
A 40 mm diameter steel bar is subjected to a tension test. Under a tension load of 276.46 kN, it was observed that the original gage length of 50 mm increased in length by 0.055 mm and the diameter decreased by 0.0105 mm. Compute the modulus of elasticity (MPa).
Determine the moment of inertia (mm4) Īx of the area shown with respect to the horizontal line that passes to the centroid of the composite area if a = 30 mm, b = 76 mm, and h = 118 mm. Round off only on the final answer expressed in whole number.
REINFORCED CONCERETERefer to the sample problem below (b = 400 mm, d= 550 mm, 4-25 mm diameter rebars). Determine if the beam is safe using the "transformed section method". sample problem: The cross-section shown below is a rectangular beam reinforced for tension only. Determine whether the section is safe or not to carry the loads shown. fs= 138 MPa. f'c = 20 MPa. n = 12. Neglect weight of beam.
Problem: Design a section of a concrete beam reinforced for tension only. The beam is simply supported on a span of 6.00 m and carries a load of 18 KN/m. Use Alternate Method of Design with n = 9. f'c = 20.70 MPa, Fy = 275 MPa. Use b = d/2. Write your solutions on clean sheets of bond paper, scan properly and uploaded on or before the due date/time. Note: Clear concrete cover for the beam: 40 mm Clear spacing between rebars: 25 mm (minimum) Minimum bar size to use as per ACI Code: 16 mm diameter Design for flexure only.
A 40 mm diameter steel bar is subjected to a tension test. Under a tension load of 276.46 kN, it was observed that the original gage length of 50 mm increased in length by 0.055 mm, & the diameter decreased by 0.0105 mm. Find the modulus of elasticity (MPa) (in whole number)
The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber= 20MPa Allowable shear strength of the steel = 200MPa Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt?
(CILO5) The composite shape in Question 5 consists of a (1) square, (2) isosceles triangle. The shape also has a hole in the form of (3) circle.a. Determine the x and y centroids of each shape based on the given axis.b. Determine the x and y centroids of the composite shape based on the given axis.c. Determine the first moment of area with respect to x axis of the composite shaped. Determine the first moment of area with respect to y axis of the composite shapee. Determine the polar moment of inertia of each shape with respect to the origin.f. Determine the polar moment of inertia of composite shape with respect to the origin