Q/ dc shunt motor 4 pole with 500 condcutor, wave running at speed 1000 r.p.m the resistance of armature and field are 0.02, 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Output of the prime motor..kwatt? 2-Torque developed by the prime mover . .and The torque developed by the armature . .. when running at 1000 r.p.m ? 3-E.M.F. generated is .volt ?

Q/ dc shunt motor 4 pole with 500 condcutor, wave running at speed 1000 r.p.m the resistance of armature and field are 0.02, 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Output of the prime motor..kwatt? 2-Torque developed by the prime mover . .and The torque developed by the armature . .. when running at 1000 r.p.m ? 3-E.M.F. generated is .volt ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *
An induction motor OF 30 HP, 220 V, 450% of the rated current with therated voltage and delivers during the starting period,with 130 % of the normaltorque. The full load efficiency and full load power factor of the motoris 80 and 70 percent, respectively. If an autotransformer is used as astarting unit and the starting torque of the load is only 50 % of therated torque of the motor, Determine the starting voltage and the startingcurrent of the line
A series dc motor 20-hp, 500-V, is having armature, series field and shunt field winding resistances of 0.08 Ω, 0.3 Ω and 125 Ω, respectively. If the back – emf is 478 V, determine the motor current when the connection is a) long – shunt. b) short – shunt c) series d) shunt
A three-phase 60 Hz induction motor connected to a three-phase bus at rated voltage isoperating at a low slip condition (i.e s < 20%) resulting in a steady state speed of 1090 rpm.(a) How many poles does the motor have?(b) What is the percentage slip at the operating speed?(c) What is the corresponding frequency, (fr) of the currents and voltages induced in therotor winding?
An induction motor of 30 HP, 220 V, 450% of the rated current with therated voltage and delivers during the starting period, with 130 % of the normal torque. The full load efficiency and full load power factor of the motor is 80 and 70 percent, respectively. If an autotransformer is used as a starting unit and the starting torque of the load is only 50 % of the rated torque of the motor, Determine the starting voltage and the starting current of the line.
Q/ dc shunt motor 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * Cu loss is……watt * Mechanical , electrical and overall efficiency …… Output of the prime motor…….kwatt * The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * Flux per pole is......... wb * E.M.F. generated is………….volt *
A 20KW, 440V, short shunt compound dc generator has full load efficiency of 87%. If the resistance of the armature and interpoles is 0.4ohm and that of the series and shunt fields 0.25ohm and 240ohms respectively, calculate the combined bearing friction, windage and core loss of the machine A 10 kW 250 volts self-excited generator, when delivering rated load, has an armature-circuit voltage drop of 5% of the terminal voltage and a shunt field current equal to 5% of the rated load current. The resistance of the armature is 0.02 ohm. Calculate the voltage generated and power output.
Assume that a motor has known frictionand windage losses described by the equation TFW = bω. Sketch the T-ω characteristic of the motorif the load torque TL is constant, and the TL-ωcharacteristic if the motor torque is constant. Assumethat TFW at full speed is equal to 30 percent of theload torque.
A 400V, 50Hz, 6-pole 3-phase asynchronous motor rotates 20Nm of constant load torque at 950rpm. If it is desired to rotate this load at 750 rpm mechanical speed;a) The synchronous speed of the motor,b) Supply frequency,c) Find the value of the supply voltage between phases?Note: The motor will be driven with V/F sbt because the load torque does not change.
The 1 phase equivalent parameters of a three phase 60 Hz, 6 pole 220, star connected, 7.5 KW asynchronous motor are as follows:a) In the case where slip is 0.03, the stator transferred rotor current, the torque and power induced in the motor.b) Maximum torque and angular velocity at this moment and speed value in rev / min.c) Developing torque and developing load currentd) Draw 1 phase equivalent circuit?
The armature, series field and shunt field resistances of a 125kW, 250V long shunt cumulative compound dc generator are 0.025-ohm, 0.01 ohm and 30 ohms, respectively. If the stray power loss at rated load is 5kW, determine the motor brake horsepower required to drive this machine. Assume a brush drop of 2V and a stray load loss of 1% of the output.
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.