Q) Determine the tension in cables BA and BC necessary to support the 60 kgcylinder as shown in figure helow., TBCSolution:Tecsin45TRAsing45X.Ta:cos0Taccos45W = mg53W =mg = 60*9.81 = 588.6 N0 = tan (3:4) = 37Σ-0Tục cos45 – TBAcos37 0(1)EF, = 0TBCsin45 + TBASin37- w 0

Sol:- Given mass of cylinder, m=60 kg Free body diagram (let tension in cables BA is T1 and BC is T2…

Answered: Q) Determine the tension in cables BA…

Engineering

Mechanical Engineering

Q) Determine the tension in cables BA and BC necessary to support the 60 kg cylinder as shown in figure helow.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Related questions

Q: Problem 6d: Find all forces acting on member ABC. The cylinder weighs 80 lb. 3 ft E 4 ft 1 ft A B 4…

A: Given data Weigh of the cylinder = 80 lb

Q: PROBLEMS 1- A ( 200 N) weight of the block shown in fig. is supported by a pin and bracket at ( A )…

Q: 2.) (2 points) The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at…

Q: The mass of the box, shown in the figure, is 145 kg. determine the tension forces in the ropes AB,…

Q: The figure below shows the hollow cylinder that each weighs 100 lb.

Q: A pulley-and-cable assembly supports block W and requires a downward force at P for equilibrium.…

Q: The cable shown in Fig. weighs 35 N/m. Determine the maximum tension in the cable and the sag ha in…

A: Draw the free-body diagram of the cable.

Q: PROBLEM 3.Rod XY and smooth surface O hold the 1600-N cylinder in equilibrium as shown. Find the…

A: Given data W=1600 Nθ1=25°θ2=55°

Q: 50°/ A 30° 00

Q: Q4. A Cylinder 1m diameter and 10kg mass is lodged between cross pieces that makes an angle of 60o…

A: x= tanθ=0.5x=Rxx=0.5tanθx=0.5tan30°=0.866m∑Fy=0N1+N2=mgdue to symmentry N1=N2=mg2=50N…

Q: Q/ Compute the pull force (F) on the rope exerted by the man to hold th crate in the position shown.…

A: Given:m=200 Kg

Q: . Determine the tension in cables BA and BC necessary to support the 60 cylinder in Figure

Q: Q2: As seen in Fig., two plant pots are supported by wires. Determine the tension in each of the…

Q: Q7. For the pulleys system in figure, determine the force P to maintain equilibrium, the weight of…

Q: 1. The box weighs 900 lb Determine the tension in each cab Ax = 7 ft 2 ft 3 ft 3 ft B 2 ft

Q: plve for the forces in wires a, b, c and d. 45° b. 60 150 lb C.

Q: A uniform brass plate with area of 18 m?, has weight of 51 kg which is hold by three cables in the…

Q: . each cable has vector, as seen in fig. Calculate the maximum mass of the sphere so that the…

Q: Determine the tension in cable BC and BA necessary to Support the 60 kg cylinder shown in the…

A: When a given system is in equilibrium, then the net external force acting on the system is equal to…

Q: A bucket, weighing 375 N, is hung from strings CAD, BA and EA, as shown in the image. Determine the…

A: Given data, Weight of the bucket, W = 375 N Since, CAD is a single string. So, tension in CA and AD…

Q: 500 N Given: Planar truss shown. Find: The force in each member of the 45 truss and determine if it…

A: The FBD at the joint B.By equilibrium equation.∑Fx=0500+FBCxsin 45=0FBC=500sin 450=707.1607N…

Q: The collar at B can freely move along the length of rod AC. Cable BD holds the collar in place while…

A: Drawing the free body diagram of the given problem,T is the tension force in the cable and N is…

Q: PROBLEM 3.Rod XY and smooth surface O hold the 1600-N cylinder in equilibrium as shown. Find the…

A: Given data: Weight of the cylinder, w = 1600 N. Draw the free-body diagram of the cylinder as…

Q: Three pairs of flexible cables, spaced at 120° inter- vals, are used to stabilize a 1000-ft…

A: Draw free body diagram of cable AC

Q: For the figure shown if P= 750 N required for the system to be in equillibruim determine the force Q…

Q: Use your assigned n value. Boom ABC is supported by a ball and socket at A and 3 cables BD, CF and…

A: Given that: mass of ball = 10*15 = 150 kg consider the given diagram, with forces drawn

Q: The climber A suspended from the rope weighs 75 kg as shown in the figure below. Determine the force…

A: Given data as per question weight of climber A =75 kg tanθ1=24θ1=26.560tanθ2=22θ2=450

Q: The homogeneous 200-lb sign is suspended from three wires. Find the tension in each wire.

A: Weight is 200lb sinθ=45 cosθ=35. ∑Fy=0 T1 is completely horizontal and Due to symmetry T2=100 lb…

Q: A uniform plank 8 ft long is balanced on a corner If using a horizontal force of 75 lb as shown in…

A: Let's draw free body diagram of 'AB' as shown in figure. Here, W=45 lb

Q: . The given system of knotted cords (label the left knot as J and the right knot as K) supports the…

Q: Q2/ For the following free body diagram compute FAF and FFD, the system is in equilibrium. FFD FO…

A: F(fd) = 2309.401lb Faf = -154.7005lb ( negative sign denotes the force is acting in opposite…

Q: 1. Determine the reaction at the roller (friction less) F for the frame loaded as shown in Fig. 1.

A: Draw the free body diagram of the member AC: Consider the equilibrium of moments about point A:…

Q: Q= 120 lb Compute the tension in cable AC. Compute the components of the reactions at supports B and…

Q: The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at point B.…

Q: 300 lb B 200 lb D ペー+ーダー

A: Answer: RA =474.34 lbFor a step-by-step solution have a look through the attached pictures of the…

Q: Find the smallest value of P for which the 400-lb crate in the figure below will be in equilibrium…

Q: Stiller Düzenlem Üst 2) A uniform brass plate with area of 18 x 18 m? has mass of 41 kg which is…

Q: Q4. A weight of 700 N was place 1 meter from the pivot as shown in the figure below. Determine the…

Q: . As seen in Fig., two plant pots are supported by wires. Determine the tension in each of the…

Q: Practice Problem 4.4.11: The bars AB 30 and AC are joined by a pin at A and a horizontal cable. The…

Q: The homogeneous 100-kg sign is suspended from three wires. Find the tension in each wire.

A: Given Mass = 100 kg To find Tension on the strings

Q: A 225 Kg crate, as shown, is supported by three cords. One cord has a spring in it. Set k= 1.5 kN/m

Q: Two men carry a load of 2 kN by means of two ropes fixed to the weight. One rope is inclined at…

A: Answer : Given parameters Weight = 2KN Inclination of rope 1 = 45o with vertical Inclination of…

Q: Find the smallest value of Pfor which the 400-lb crate in the figure below will be in equilibrium in…

Q: The uniform bar AB shown in Fig. 30 lb. If the spring is unstretched when 8 = 0°, determine the…

A: Weight of the uniform bar, Length of the bar AB, Spring is unstretched when,

Q: A traffic light of mass 5 kg hangs from two lightweight cables, one on each side of the light. Each…

Q: Q/ Compute the pull force (F) on the rope exerted by the man to hold the crate in the position…

Question

Q) Determine the tension in cables BA and BC necessary to support the 60 kg
cylinder as shown in figure helow.
, TBC
Solution:
Tecsin45
TRAsing
45
X.
Ta:cos0
Taccos45
W = mg
53
W =mg = 60*9.81 = 588.6 N
0 = tan (3:4) = 37
Σ-0
Tục cos45 – TBAcos37 0
(1)
EF, = 0
TBCsin45 + TBASin37- w 0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

F= 45.59 N What is the loading in DB and CB in Tension or Compression?
Application of Equilibrium Solve for the value of unknown variables Given : P1 = 6.85 KN P2 = 4.65 KN W1 = 6.15 KN/m Unknowns : RAy , RAx ,RBy , MA What is the value of internal shear 2.50m to the right of support A
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 48.7N shown in the figure. Take, α = 29.4° & β = 47.5°. a) The value of θ1 (Degree) = b) The value of θ2 (Degree) = c) The value of θ3 (Degree) = d) The value of Tension, T1 (N) = e) The value of Tension, T2 (N) =
Shown in the following figure is a foldable table loaded by weight “W”. The contact points, B, D, and E are frictionless. 1. Find the safest load W if the allowable tensile force in the cable is 1800 N. a. 600Nb. 180 Nc. 482Nd. 630N2. If W = 1500 N, find the reaction at D. a. 500 Nb. 1000 Nc. 800 Nd. 1200 N3. If W = 1500 N, find the reaction at B.a. 500 Nb. 1000 Nc. 800 Nd. 1200 N
Statics-Two Force Members 1. Determine the force P required to maintain equilibrium of the pulley system, and the reactions at the ceiling. 2. Assume W=1.25kN 3. Show and clearly label all Free Body Diagram to determine solution.
The positive directions are indicated in the figure. The system is in static equilibrium. 1. For the forces applied on point B, determine the component BAx =__N 2 Determine the component BAy=__N 3 Determine the component BDx=__N 4. Determine the component BDy= __N 5. Determine the component of force BD =__N 6. For the forces applied on point D, determine the component DBx=__N 7 Determine the component DFx=__N 8 Determine the component DFy =__N 9 Determine the tension in cable DF, Tdf=__N 10. The system is in static equilibrium determine the angle =__° 11. Determine the distance d=__m
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work. These are my answers FBD=2F, RAX=353.5N RAy= 353.5N but am not sure if a correct any help
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work.
What is Equilibrium of a Rigid Body? Give an example.
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
The J-shaped member shown in the figure (Figure 1) is supported by a cable DE and a single journal bearing with a square shaft at A. Determine the reaction forces A_y and A_z at support A required to keep the system in equilibrium. The cylinder has a weight WBWBW_B = 24.0 N, andF = 7.60 N is a vertical force applied to the member at C. The dimensions of the member are w = 0.450 m , l= 2.00 m , and h = 0.600 m .