Answered: Q- If the BOD3 of a wastewater sample…

Q- If the BOD3 of a wastewater sample is 75 mg/L and reaction rate constant k (base e) is 0.345 per day, find the amount of BOD remaining in the given sample after 10 days.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: REQUIRED: GIVEN: H = 32.5m hla= 1.4m hib = 1.6m AB = 3.8m B = 40° FIGURE: A 3.8m B B1=44⁰ h₁a = 1.4m…

Q: Stable or unstable?

A: To determine weather a truss is stable or unstable. We need to determine, Degree of static…

Q: A column is supported on a footing as shown in the figure below. The water table is at a depth of 1…

A: Given figure of a column: Factor of safety = 3, Area, A = 1.5 m × 3 m = 4.5 m

Q: Use the cantilever method and determine (approximately) the reactions at supports A and B. All…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subpartsfor…

Q: Problem Water is flowing through a pipe of diameter 200 mm with a velocity of 3 m/s. Find the head…

A: Given Diameter D=200 mm =0.20 m, Velocity V=3 m/s, Length L=5m, Kinematic Viscosity ν=0.01 stoke…

Q: HYDROSTATIC FORCE ON PLANE SURFACES I need help analyzing my experiment. For a Fully Submerged…

A: Data given

Q: anwser (5)

Q: A company which manufactures electric motors has a production capacity of 200 motors per month. The…

Q: VI. The force R is the resultant of the three forces P₁, P2, P3. P₂ if R= 45 KN acting on the…

A: Objective: To determine the forces P1 and P2 for the given system of forces. Given: R = 45 kN P3 =…

Q: Water flows in a rectangular channel with a flow rate Sms, and specific energy diagram. Determine…

A: Answer (1) Calculation of Minimum specific energy Based on the given data and specific energy graph…

Q: For the joint shown: a. calculate the largest bearing stress (MPa) between the pin and the members.…

Q: Why do we have to trim the soil sample in undisturbed soil carefully using the soil lathe? What are…

A: Undisturbed Soil Sample: Here natural properties and structure of soil remain preserved. Gathering…

Q: diagram

A: Consider 2nd part of the beam

Q: Write the 17 system of forces as an equivalent force Couple System at A. B 50° 130⁰ F₂ TA t ) 2m: 2m…

Q: 20. What are the cross sectional area, leg dimensions and thickness of an L6x4x1/2? (Hint: Use your…

A: AISC is the american standard code for the design of steel construction.

Q: Determine the magnitudes of cable 2 and 3 for equilibrium. Consider force at cable 1 is 300N and W…

Q: Determine the shrinkage limit.

Q: As shown in the figure, a rigid beam with negligible weight is pinned at one end attached to two…

A: W=200kN To find vertical displacement of load W

Q: In a lifting machine in which velocity ratio is 30, a load of 5000 N is lifted with an effort of 360…

Q: A triangular open channel has a vertex angle of 90° and carries flow at a critical depth of 0.30m…

Q: *3-36. If the bucket and its contents have a mass of 200 N and are suspended from the cable by means…

Q: Use the cantilever method and determine (approximately) the reactions at supports A and B. All…

Q: Determine the reactions and the force in each member of the space truss. Indicate if the members are…

A: Given:- A space truss is given The magnitude of the force at point D = PY = 500 lb To determine:-…

Q: 294

Q: Q2: Water flows in a rectangular channel with a flow rate 5m³/s, and figure (1) shows the specific…

Q: what is its specific weight? *

Q: PROBLEM TO SOLVE: 600 mm 400 mm +6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given data in question Load 35, 66 and 35 kN Span member length 4.3 m and 3.1 m Make use of the…

Q: Two tugboats are towing a cargo ON and tugboat B exerts a force of 2 pats with just a single force.…

Q: Question-7 A horizontal circular curve with a centre line radius of 200 m is provided on a 2-lane,…

A: Given data: A horizontal circular curve with center line radius, R = 200 m For 2- lane, 2- way SH…

Q: A motorist is travelling at 72 kph when he observes the traffic light 150 m ahead of him turns red.…

Q: Question A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given : thickness of plate= 12mm connect to 8mm thick plate 2×8>12 hence t= 12mm Dia of rivet…

Q: What is the difference between charpy impact test and izod impact test?

A: Difference between Charpy and Izod impact test

Q: What other types of prototyping are possible

A: prototype: A prototyping system is a system development technique in which a working model for…

Q: 9. What are the nominal and actual depths of a W16×100 wide-flange member? What is the weight of…

A: Find out nominal and actual depth of W 16x100 what is the weight per foot .?

Q: a). Determine the atomic and equivalent weights of Na+ and Ca2+. A water sample contains 102 mg/l…

A: Answer (a) For Sodium Na+ Atomic weight(AW) of Na+ = 23 g Na+/ mole Equivalent weight(EW) of Na+ =…

Q: A pipe-line carrying water has average height of irregularities projecting from the surface of the…

Q: 2. The force P = 2 kips is applied to point A, and is supported by cable AB, cable AC, and bar OA.…

Q: Determine variables requested below for a horizontal curve with the following characteristics.…

A: given- length of curve= 1255' radius of curve=1200' sta of PC 12+00 ROADWAY IS THREE LANE. design…

Q: In the cylindrical coordinate system, stress component Trz = 23 N/m². Trz acts on a surface (shown…

A: Given data : shear stress on r-plane along z direction = 23 N/m2 area of plane = 40 inch^2 find out…

Q: Determine the force in each member of the space truss and state if the members are in tension or…

A: The given figure is shown below:

Q: The scale on the map is 1: x. A lot having an area of 640 sq.m. is by an area of 25.6 cm² on the…

Q: 2 m Part A D A Part B 1.5 m B -1.5 m 0.3 m C F. Consider the frame shown in (Figure 1). Suppose that…

Q: Problem A horizontal venturimeter with inlet and throat diameters 30 cm and 15 cm respec- tively is…

A: Given Diameter at inlet D1=30 cm, Diameter at throat D2=15 cm, Reading of differential manometer…

Q: Given the FLEXURAL RIGIDITY=6000 :KN.m^2. The deflection value at point A is A 9m 50 KN -0.025 mm…

A: P=50kN L=9m EI=6000kN-m2 To find deflection at point A of cantilever beam

Q: Calculate the forces in members AB, BG, and GF. Solve for each force from an equilibrium equation…

Q: Find the solution of the differential equation = A. y = x B. y=x-x* C. y = √x-x4 D. y=x-1 E. Not in…

A: The given differential equation, dydx=2y4+x4xy3 To find the solution of differential equation.

Q: 2. Determine the forces in member BC, BE and EF of the truss shown in the figure by Method of…

Q: tes A 48-kg crate is attached to a trolley-beam system as shown in the figure. Know that a = 1.5 m.…

Q: A -6% grade and a +2% grade intersect at STA 12 + 200 whose elevation is at 25.632 m. The two grades…

Concept explainers

Integrated Solid Waste Management

Integrated Solid Waste Management (ISWM) is a thorough waste suppression, compost, removal and recycling Program. An effective ISWM system considers how to suppress, manage and recycle solid waste in a manner that is most efficiently to protect human health and the surrounding. ISWM system requires evaluation of public wants and demands and then selecting and merging the most effective waste management activities for the proposed demands. The main ISWM activities for solid waste management are Waste prevention, Recycling and Composting, and Combustion and Removal and waste collection in a properly planned, constructed, managed and mitigated landfill areas. Each of these requires careful designing, financing, accumulation, and delivery of activities.

Question

Q- If the BOD3 of a wastewater sample is 75 mg/L and
reaction rate constant k (base e) is 0.345 per day, find the
amount of BOD remaining in the given sample after 10 days.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine ultimate BOD for a wastewater having 5 day BOD at 20o C as 160 mg/L. Assume reaction rate constant as 0.2 per day (base 10).
the BOD2 and BOD6 of a sewage sample is 250 mg/L and 50 mg/L respectively.calculate BOD after 4 days
The ultimate BOD of two wastewaters is 280 mg/L but their K values are 0.1/d and 0.23/d at 20oC. Calculate 5-day BOD for each of the wastewater. What you conclude based on your answer?
The average design flow at a wastewater treatment plant facility is 1.5 m3/s. The bar rack is mechanically cleaned with an average clear spacing of 2.5 cm. Estimate the average quantity of screenings that will be collected at each day.
The BOD 2 and BOD 6 of a sewage sample is 250 mg/L and 50 mg/L respectively.Calculate BOD after 4 days?
A tannery of processing plant with a wastewater flow of 0.011 cu.m/s and a BOD5 of 590 mg/L discharges into the river. The river has a 10 year, 7-day low flow of 1.7 cu.m./s. Upstream of the tannery, the BOD5 of the river is 0.6 mg/L. The BOD rate constants (k) are 0.115 day-1 for the tannery and 3.7 day-1 for the river. Calculate the ultimate BOD of the tannery wastewater, in mg/L. a. 1,972 mg/L b. 2,155 mg/Lc. 1,350 mg/L d. 1,264 mg/Le. None of these
A COD test is carried out on a batik factory wastewater. The relevant information is as follows. Volume of potassium dichromate standard solution 0.1N = 10.0mL Volume of wastewater sample = 20.0mL Wastewater sample dilution = 10X Fe^2+ standard solution = 0.1N Volume of Fe^2+ standard solution needed for wastewater sample = 13.55 mL Volume of Fe^2+ standard solution needed for distilled water = 34.70 mL. Calculate the COD value for the batik factory wastewater.
The BOD2 and BOD6 of a sewage sample is 250 mg/L and 50 mg/L respectively. Calculate BOD after 4 days?
Civil, Environmental Laboratory determinations of an industrial wastewater indicate that its ultimate BOD is 750 mg/L and the k value at 20°C is 0.20 day¹. Calculate the 5-day BOD. What would be the 5-day BOD, if k value dropped to 0.1 day ¹?Note: Ultimate BOD=L=L,
In a BOD test, the amount of organic matter remaining in the wastewater was measured at certain time intervals, instead of measuring the dissolved oxygen content. The amount of organic matterremaining after 4 and 9 d was measured as 52.86 mg/L and 8.11mg/L, respectively. Calculate the ultimate BOD and BOD rate constant k for the wastewater.
Q/ Find the BOD of trickling filter effluent if the BOD of raw sewage is 250 mg/l with 125% recirculation. The flow is 3.15 m/min and tank volume 860 m .Assume 35% BOD is removed by primary sedimentation tank using the NRC equation.
A 3 mL industrial wastewater sample is added to a BOD bottle (300mL). The initial D.O. concentration is 11.2 mg/L. After five days the D.O. concentration is 3.6 mg/L. Calculate the BOD 5 in mg/l