Q/ The fuel costs of two Power Plants are 2 f₁ = P₁ + lop₁ + 25 Rs./h M 2 2 fr= 0.7 P₂ +6P₂ + 20 Rs/h 2 If the two generating units together supply a total load of 220 MW. then find (1) the out fut Power of each unit (2) the incremental fuel costs.

Q/ The fuel costs of two Power Plants are 2 f₁ = P₁ + lop₁ + 25 Rs./h M 2 2 fr= 0.7 P₂ +6P₂ + 20 Rs/h 2 If the two generating units together supply a total load of 220 MW. then find (1) the out fut Power of each unit (2) the incremental fuel costs.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Related questions

Q: Draw the equivalent circuit model and switching characteristics of the device which is having…

A: Introduction - IGBT is a stands for insulated-gate bipolar transistor. It is a power transistor…

Q: Subject:Electronics Engineering What is the main constructional difference between D-type and…

A: MOSFET: It stands for Metal oxide semiconductor field effect transistor. It is used as a voltage…

Q: 1. A transformer takes 10 A on no-load at a power factor of 0.1. The turn ratio is 4 : 1 (step…

A: A transformer takes 10 A on no-load at a power factor of 0.1, turn ration N1:N2=4:1 (step down). If…

Q: Find the current I4 and the voltage V2 for the network

Q: 1. A source voltage of an AC series RLC circuit is 120 V. The circuit consists of the ff.…

A: 1. A source voltage of an AC series RLC circuit is : Vs=120 VoltR=20 ΩXL=40 Ω so, ZL=jXL=j40…

Q: 6- The weekend was boring, (I didn't/ don't) do anything useful.

Q: 4. A long solenoid with 190 turns produces a flux of 3.6 x 10-5 Wb (through a plane normal to the…

A: Given data, N=190 ϕ=3.6×10-5 WbI=4.2 A

Q: 1. An inductive coil having a 30 om resistance and unknown inductance is connected in parallel with…

Q: Q2: for figure 1, find IL 380/0° V 380/120° V P for load and S for source? " ▷ a Ia 380-120° V Ib I…

A: In this question, We need to determine the load current IL , active power P and Apparent Power…

Q: Example: Reduce the system shown in Fig, to a single transfer function C(s)/R(s). + R(s) + V₁(s)…

Q: Q1/ For the following network: (a) write the mesh equations. (b) find the current Is through the…

Q: The terminal voltage of a 3-φ generator is 19053 V, line-to-line. The load draws a current of 2727…

Q: (a) U Let x[n] = {1, 2, 0, 0, 4). What is the energy in x[n]?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Determine the voltage V, in the circuit of Fig. 1

Q: Find the total capacitance of the combination of capacitors shown 5.0 μF 1.5 μF 3.5 μF 0.75 μF 15 μF…

A: Given A circuit made of capacitors, we need to find the equivalent capacitance of the circuit.…

Q: of charge. The cell has a constant internal resistance of 0.01 Q and reversible

A: Current: I=dqdt Heat: H = I2Rt

Q: 33. The efficiency of a 400 kVA, 1-phase transformer is 98.77 % when delivering full load at 0.8…

A: Here, we discuss about the concept related to the efficiency of a single phase transformer.…

Q: Example 7.6 Determining the Step Response of an RC Circuit The switch in the circuit shown in Fig.…

Q: The plates of a capacitor are of conical shapes and are defined by the surfaces 0 = 27° and 9 = 66°.…

A: The Given data is The Surface of the conical shapes is ϕ1=27°; ϕ2=66° The Height of the both…

Q: 3. MOV AL,[BX] is an example of - 4. MOV CL,[DI]+20 is an example of ---- 5. MOV CL,[BX][DI]+6 is an…

A: As per the guidelines of bartleyby I need to answer first three questions only.

Q: Question 4 An AC Voltage v(t) = 250 cos (100nt) is applied to the given circuit. ~ V (1) sine…

A: Brief description: For the given sinusoidal voltage function we need to derive peak, peak to peak ,…

Q: 2- What is the role of emitter bypass capacitor CE in CE amplifier circuit shown in Fig. ?

A: The impedance of the capacitor is infinity for DC power supply whereas the value is finite for AC…

Q: Solve the current I1 in the given circuit using Norton's Theorem

A: The given circuit is as shown below,

Q: The output signal from a DSBFC AM modulator is u(t) = 5 cos 1800nt + 20 cos 2000nt + 5 cos 2200nt.…

Q: (Note that VO=V01+V02, where Vo1 is due to V1 and Vo2 is due to 11) V02 (in volt) due to 11 only= O…

Q: If your power output is 108W, and the mass of the bucket and the water in it is 6.00kg, with what…

A: Given, Power output, P = 108 W The combined mass of the bucket and water, m = 6 kg Acceleration due…

Q: A circular loop is oriented 35.0 degrees to a 0.752 T magnetic field. If the magnetic flux through…

A: Given, Magnetic field, B=0.752 T Magnetic flux, ϕ=0.0303 Wb Orientation of circular loop with…

Q: Calculate the amount of energy stored in a laptop battery that requires 2 hours to charge from 0% to…

Q: Find the total capacitance of the combination of capacitors shown 5.0 μF 1.5 μF h 3.5 μF 8.0 μF I…

A: In this solution we calculate the equivalent/total capacitance of given circuit.

Q: For a process described by the following FOPTD model. Find the suitable Pl controller .parameters…

A: Given the FOPTD model transfer function, ysus=12s+1

Q: H.W: Find the Parallel Realization for : 22 H(Z) (3-1) (2-0.5)

Q: Find the overall impulse response of the system below, where hy(t) = 2u(t-3). h₂(t)=3eu(-t). hs(t) =…

A: given here system and asked to find the impulse response of overall system. we know that…

Q: A current 0.25 A exits in a 60-ohm lamp. The potential difference is

A: Given data, Current is given I = 0.25 A Resistance is given R = 60 ohm.

Q: Determine the approximate value of drain voltage (VD) of the given circuit below. VOD 120V 18.33 V…

Q: Show and construct the circuit so that full adder can converted to a full subtractor with the…

A: The Full adder Circuit is shown below. Where, sum S=A⊕B⊕Cin Carry Cout=AB+ACin+BCin

Q: A continuous random variable X had a pdf shown below. Find (A) K, and (B) P{X>1).

Q: 3. Calculate the following: a) voltage drop across Rs; b) current flow through Rs; and c) power…

A: Circuit diagram is given as,

Q: -1500 8012 300 www -200 10 c

Q: Determine the approximate value of drain current (ID) of the given circuit below.

A: Iv/s=0ID≃IsRs=910 Ω=0.91 kΩApply KVL in o/p…

Q: In Industry, three Inductive loads, each of resistance R = 22 ohms and inductance L = 0.07 H in…

Q: 3s - 14 s²4s +8 3e²t cos 2t + 4e²t sin2t Option 1 4e²t cos 2t + 3e²t sin2t 2t 2t Option 3 3e2t cos…

A: inverse laplace transform find by sinple partial fraction and making perfect sqare in denominator is…

Q: a circuit armature of a 4 pole generator has 51 slots , each slot containing 20 conductors . What…

A: The emf induced in the generator is given by the expression as shown below: E=PϕNZ60A If the winding…

Q: Section 2.2 Zener Diode Circuits 2.19 Consider the circuit shown in Figure P2.19. The Zener diode…

A: Given: Zener voltage, Vz=3.9V,internal zener resistance, rz=0

Q: Q1/ The following information is given for a 250-kW, 500-V, long-shunt compound generator : Shunt…

A: The terminal voltage of the generator is 500 V The power produced is 250 kW The armature resistance…

Q: Q14- If f(x,y) = 2xy - x² In y- 2y² + 3x + 4, is : then a²f axy for the function

A: 14) To find d2f/dxy for the function f(x,y) First, differentiate f w.r.t any one variable assuming…

Q: Design a 4-bits sequential detector that detects the code 1011 Using (D Flip flop)) please give me…

A: The Delay flip-flop is made using a gated SR flip-flop, it is a clocked flip-flop with a single…

Q: 2) Calculate the critical sampling rate for the following signals: i. y(t) = cos(10πt + 20°) +…

A: In this question we need to find a critical sampling rate of the given signal. Critical sampling…

Q: The joint pdf of the two R.V. X and Y is giving by the below Figure. Find (1) the marginal pdf's of…

Q: Q2: For the ideal op-amp shown in figure (2). Find: 1. The voltage gain A, = V₂/V₁? 2. The input…

Q: Multiple choice questions: 1- A voltages of 50Hz transformer are 1500 V on primary and 600 V on the…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

Q/ The fuel costs of two Power plants are!
2
f₁ =
P₁ + lop, + 25 Rs./h
2
2
f2
P₂ +6P₂ + 20 Rs./h
2
If the two generating units together supply
a total load of 220 MW. then find (1) the
out Put Power of each unit (2) the incremental
fuel costs.
20
M
A
1
(

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I have just started my first Semester (Fall 2021) out of 4 semesters in Master of Applied Science (M.A.S) in Power Engineering at Illinois Institute of Technology. I did not clearly undersand the course enrollment system because I am new to the system, so I ended up enrolling in courses; ECE58-Microgrid Design and Operation, and ECE579-Computer Aided Design of Electrical Machines. It appears ECE582 listed ECE418 (Power System Analysis) as a prerequisite; and ECE539 requires ECE319 (Fundamentals of Power Engineering) and ECE412(Hybrid Electric Vehicle Drives) as prerequisites. Let me hasten to add that I graduated in 2009 in a different academic setup in Africa in Electrical Engineering. So, not only do I have to cover the gap of about 12 year out of classroom, but I have compounded the problem by jumping into advanced courses before enrolling into foundation courses. Unfortunately I can no longer switch courses as the enrollment window has passed. I am only left with one option; to…
S1) The serial impedance per unit length of a three-phase 140 km power transmission line is 0.09 + j0.88 ohm/ km and its admittance is j4.1x10-6 S / km. Power factor under 210 kV interphase voltage from the end of this energy transmission line A power of 150 MVA, which is 0.85 back, is drawn. Using this transmission line data and the T equivalent circuit model, the line Calculate the head voltage (V1), current (I1) and load angle.
Use dynamic programming method to determine the most economical units to be committed to supply a load of 350MW and 450 MW. Generation is varying in step size of 50MW. There are two units with the following data: C1 =0.005 P12 + 6.2P1 +300 RO/hr C2 =0.003P22 + 6.0P2 + 200 RO/hr Where P1 and P2 are in MW. Plant outputs are subject to the following limits(in MW). 50 ≤ P1 ≤ 350 100 ≤ P2.≤ 250
2. Frame a priority list for supplying a load up to 2000 Mw in the given power plants Plant J: Fl = (2 + 0.003 PI) 103 k-cal/Mw-hr. P1= 500 MW Plant 2: F2 = (6.5 + 0.006 P2) 103 k-cal/Mw-hr P2 max = 300 MW Plant 3: F3 = (6 + 0.005 P3) 103 k-cal/Mw-hr P3 max = 240 MW The fuel costs at the plants are given by CP I=0.92 RO/kcal CP2 = 1.05 RO/kcal CP3 = 1.2 RO/kcal
Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
Urgent. An office space measures 50ft x 90ft with 16ft high walls. A 1.25 air changes per hours is desired for this space. Find the heat loss (in btuh) when the indoor temperature is 70°F and the outdoor temperature is 36°F. Select one: a. Q = 56,100 btuh b. Q = 44,880 btuh c. Q = 37,736 btuh d. Q = 75,900 btuh e. Q = 64,350 btuh
Q4. Economic analysis of the electricity market is an essential part of the operation of modern power systems. (A) The concepts of economic dispatch, load flow and optimal power flow are widely used in power system analysis. Define the optimal power flow problem and discuss how it differs from load flow and economic dispatch problems. Discuss the likely impact of the rapid adoption of renewables on the optimal power flow problem.
Consider a Pumped storage micro-hydel plant is to be built as a Peak load-plant on above mentioned Nathiya-Galli Water Fall with available head of 39 m and average discharge of 5640 m³/hour from the upper pound. The hydraulic efficiency and electrical efficiency of the plant to be 0.86 & 0.92 respectively. Analyze the following output from the above Pumped Storage Plant: a. Hydro-Power and Annual Hydro-energy available b. Electrical Power and annual electrical energy units that can be generated from the plant.
4. A hydro-electric plant has a catchment area of 120 km². The available run off is 50% with annual rainfall of 100cm. A head of 250m is available on the average. Efficiency of the power plant is 70%. Find () average power produced (1) capacity of the power plant. Assume a load factor of 0.6.[t)
. A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If the station has a load factor of 35%, solve the demand factor of the station. Answer: 0.4179 or 41.79% Subject: Distribution System and Substation Design
A colliery workshop 20mx10m requires an averageillumination of 135 lm/m 2 on the working plane. Allow acoefficient of utilization of 0.45 and a depreciation factor of1.4. The supply is 230-V at 50Hz and the efficiency of each ofthe lamps is 12 lm/W.16. Calculate the electrical power required for thepurpose.A. 8 kW B. 4 kW C. 3 kW D. 7 kW17. Calculate the current required for the purpose.A. 34.3 A B. 21.2 A C. 26.9 A D. 30.4 A
1- Your company is considering the installation of a 2 MW wind turbine with a rotor diameter of 80 m in a location with average wind v = 10 m/s. The turbine has a cut-in velocity of 5 m/s and a cut-out velocity of 25 m/s. The capacity factor is 0.45. The installed cost of the turbine is $3,500,000. Operating expenses are $225,000 per year. The system has a power coefficient (electric power generated divided by wind power) of 0.45. What price would you have to get for the electricity you produce to obtain a 10% return on the plant investment assuming a project lifetime of 20 years? Use the tables for the cumulative wind power distribution in the notes on wind probability to answer this question. Assume an air density of 1.225 kg/m3.