Question 4 An AC Voltage v(t) = 250 cos (100nt) is applied to the given circuit. ~ V (1) sine Calculate: (a). The peak (V₂) and peak to peak (Vp-p)voltage. (b). RMS value of the applied voltage. (c). The frequency (f) and time period (7) and phase p ww R1 250

Question 4 An AC Voltage v(t) = 250 cos (100nt) is applied to the given circuit. ~ V (1) sine Calculate: (a). The peak (V₂) and peak to peak (Vp-p)voltage. (b). RMS value of the applied voltage. (c). The frequency (f) and time period (7) and phase p ww R1 250

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2MCQ: If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by...

See similar textbooks

Related questions

Q: Knowing that the open loop transfer function is vā (s) 1 s²+9s +21 And the closed loop block diagram…

Q: For the circuit shown in figure, determine the current and voltage for the resistor R3 using the…

A: We need to find out the current and voltage for given circuit by using of superposition Theorm

Q: Choose the correct answer for the following: x The components of the propagation constant are named…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: 4. Transform the following from circuit diagram to breadboard diagram and breadboard diagram to…

A: The given breadboard connected circuit can be converted into a circuit by finding the series and…

Q: 5) Find Vo in the circuit below using Thevenin Theorem 12V R + ΛΑ 2 ΚΩ 2 Vx 2000 2 ΚΩ R + - 2 ΚΩ Re…

Q: Q2: The op amp in the circuit shown in Fig. 2 is ideal. a) Calculate va when vg equals 4 V. b)…

A: Question 2: For the given op-amp circuit in fig,(2) calculation of following : calculate the va…

Q: 2. Using KCL, find the unknown currents (11, 12, 13 and 14 ) for the network shown in the Figure 3.…

Q: -2 units, 10 = 700 MW/ 3 F₁ = 10P₁ + 8×10³ P₁² (/hr) _F₂=8P₂ +9910² P₂² ($/hr) 3 Find P, and P₂…

Q: An electric dipole at 40° with respect to a uniform electric potential of (x²+y+cosz) volt,…

A: To find the magnitude of dipole moment at point p(-2,1,3) Given : electric potential, V = (x2 + y +…

Q: What is the emitter voltage in figure 10 V 250 kQ2 de F 10 μF 1.8 V O 0.7 V O 1.3 V O 2.4 V 47 ΚΩ HH…

A: We need to find out the emitter voltage for given circuit

Q: RB 1kQ2 IB V BE +Vcc=20V • Rc = 4.7 ΚΩ Ic IE RE= 10 kn -VEE -20V

A: given here a circuit and asked to check the approximation can be used or not. we know that VBE =…

Q: 3. Describe the Volts per Hertz Control for three phase induction motor.

A: Tere are numerous speed controlling techniques of the three phase induction motor .In such motors we…

Q: Two resistors are connected in parallel as shown in the figure. What is the value of R, and I7? + VT…

Q: Q1/ Draw the bode plot below on the semi-log paper and find GM and PM for G(s)H(s) = 1…

A: The bode plot can be drawn by converting the transfer function into bode form and then calculate the…

Q: Example 7.6 Determining the Step Response of an RC Circuit The switch in the circuit shown in Fig.…

Q: Calculate the average power þ Power Factor ww 8N N -jun 5010° deliverd by the 62 ww 11 fir source.

Q: te of charge to 67% state of charge. The cell has a constant internal resistance of 0.01 and…

A: The formula is given as, Current: I=dqdt Heat: H = I2Rt

Q: Q3) Calculate la, the induced e.m.f., and the output of prime mover for a short-shunt compound…

A: V=380+0.5×50V=405 VIsh=VRsh=405 V190 Ω=2.13 AArmature current Ia=Ish+IL…

Q: C- True and False (correct the false) 1- Class-A: the output stage conducts for a full 360° (a full…

A: Given True or false questions based on power amplifiers. Please find the below attachment for clear…

Q: Find the unknown values. 892 ww 30 V Disregard negative sign. i₁ = A 1₂ = A V₁ = V2 = V3 = + V + 5…

A: given here a electrical circuit and asked to find the i1 , i2 , v1 , v2 , v3 .

Q: a) Calculate the line currents, the power consumed (consider the internal resistance of the coil)…

A: As per Bartleby policy we can answer only one question at a time. Please repost it for other…

Q: find Ishort circuit and 5A Rnorton 8222 M 5V 8212 {50-2 M 330 M ≤39-22

A: Steps to find Norton Resistance and short circuit current To find the Norton Resistance, short the…

Q: A blocked rotor test was performed on a given condition: Po = 5 Hp, 60 cycle, 115 volts,p = 8pole,…

A: Given A blocked rotor test was performed on a given condition: Po = 5 Hp, 60 cycle, 115 volts,p =…

Q: Explain which is more safer in aircraft operation GPS OR differential GPS

A: Difference between GPS and DGPS: GPS DGPS Full form of GPS is Global Positioning System. Full…

Q: Show and construct the circuit so that full adder can converted to a full subtractor with the…

A: The Full adder Circuit is shown below. Where, sum S=A⊕B⊕Cin Carry Cout=AB+ACin+BCin

Q: + 1 V₂ 552 [mm] 12mH 5mH n 1.82 M 35mf

Q: + E 15 R1 6 D1 R2 3 -V2 -V1

Q: Let x[n]={1,2,5,-1} . Generate x[2n] and various interpolated versions of x[n/3] ⇓ ii. Let x[n] =…

A: i) Let x[n]={1,2,5,-1}. We need to generate x[2n] and various interpolated versions of x[n/3]. ii)…

Q: Example 7.6 Determining the Step Response of an RC The switch in the circuit shown in Fig. 7.22 has…

A: In this question we will find capacitor voltage and current for time greater than zero...

Q: rotor position are the A. field-effect sensors. B. optical-range sensors. C. hall-effect sensors. D.…

A: There are few questions related to the sensors attached with the machine in order to measure the…

Q: Q2: For the ideal op-amp shown in figure (2). Find: 1. The voltage gain A, = V₂/V₁? 2. The input…

Q: e-2t (cost + 3 sin t) 8 2 3 + (s−2)² +1 (s+ 2)² +1 Option 4 s 5 s² - 4s +5 Option 2 8+2 (s+ 2)² +1…

Q: what happens when a modulated signal is passed through a white Gaussian noise channel

A: A channel is said to be white gaussian channel if in the channel white noise is present. The…

Q: Compute the capacitance of a parallel-plate capacitor with plates 10 cm by 20 cm and separation of 5…

A: (i) The given capacitor is a parallel plate capcitor. The capacitance of the parallel plate…

Q: b) For kretsen i Figur 3, beregn total resistans (RT). R1 = 4kQ R3 = 8kQ R2 = 1kQ Figur 3. Krets for…

Q: 1. Use Green's Theorem to evaluate JC (5y-9x)dy-(yx-x) dx where C is shown below

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 4-A 1-phase transformer has 180 and 90 turns respectively in its secondary anc windings. The…

A: In this question we will find single phase transformer Resistances referred to primary and secondary…

Q: reactance Rp = 3-ohm Xp = 15-ohm Rs = 0.03-ohm Xs = 0.15-ohm Find the primary voltage required to…

A: Solution- Ans- Equivalent circuit of 1- phase transformer referred to primary,…

Q: digital signal prossesing

A: The solution is provided in the following section.

Q: Determine the diode current

Q: Draw the equivalent circuit of long transmission line and derive the equations of sending end…

A: Types of Transmission line Long Transmission line Medium Transmission line Short Transmission…

Q: 4. β = 100. Check if approximation can be used. Show calculation proof. If yes, use approximation…

A: Here we discuss about the calculations using voltage divider circuit & approximation method.

Q: Use the analytical method, design a lossless L-section network to match a load impedance of 30+j15Q…

A: L-section matching network:- This network consists one reactive element which is in series and also…

Q: what is the curret gain?

A: BJT (bipolar junction transistor)A transistor having a three terminal made up of semiconductor…

Q: . The _________ can actually be used as a voltage-controlled resistor because of a unique…

Q: 2) What are the salient features of supply voltage control method?

A: Voltage Controller: A voltage controller, also known as an AC voltage controller or AC regulator, is…

Q: The output of the 3-phase, 425 V induction motor is 18 kW and operates at power factor of 0.65…

A: Given data: Output power, P0=18 kW Power factor, cosϕ=0.65Efficiency=83%

Q: Develop the following problems in a clear and orderly way. Use 4 decimal places for magnitudes, real…

A: Overall system is balance, hence it can be solved by per phase equivalent circuit. Assume both the…

Q: 3) Find Io in the circuit below 4 ΚΩ 2 mA 6 mA 2 ΚΩ Io 12V Ε Σ4 ΚΩ

A: In this question we need to find a current Io of the given circuit.

Q: AM signal is generated by modulating an 800 KHZz carrier by the gnal m(t) = cos 2000nt + 2 sin…

Concept explainers

Fourier Series

Most of the incidents studied in the field of Engineering and Science as a function of time. For example, current and voltage are in the alternating current circuit. These occasional activities can be analyzed in the activity components (fundamental frequency and harmonics) through a process called Fourier analysis.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three sinusoidal alternating currents of RMS 5, 7.5, and 10 A are having the same frequency of 50 Hz with the phase angle 30, -70, and 45 degrees respectively. Find the average value in amperes. choices: a. 4.5, 6.76, 9.0 b. 5, 7.5, 10 c. 5.56, 8.83, 11.11 d. 6.0, 8.0, 10.0 Refer to previous problem, write the equations for their instantaneous current in ampere values. choices: a. i1 = 7.07 sin(314t + 30), i2 = 10.61 sin(314t + 70), i3 = 14.14 sin(314t + 45) b. i1 = 7.07 sin(314t + 30), i2 = 10.61 sin(314t - 70), i3 = 14.14 sin(314t + 45) c. i1 = 7.07 sin(314t - 30), i2 = 10.61 sin(314t - 70), i3 = 14.14 sin(314t + 45) d. i1 = 7.07 sin(314t - 30), i2 = 10.61 sin(314t + 70), i3 = 14.14 sin(314t + 45)
Two equal voltages are out of phase with respect to each other by 90 electrical degrees. If the resultant is 311 Volts, what is RMS value of each one?-write legibly-show the complete solution
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The raveling wave propagation speed in the tower is 1.2* 108 m/s. i) Determine the voltage reflection coefficients at tower top and tower foot. ii) Ignoring the phase voltage, determine the insulator voltage after 2µs.
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The raveling wave propagation speed in the tower is 1.2* 108 m/s. i) Determine the voltage reflection coefficients at tower top and tower foot. ii) Determine the time of travel from tower top to tower foot. iii) Determine the time of travel from cross arm to tower foot. iv) Draw the voltage lattice diagram with proper labels of the time. v) Ignoring the phase voltage, determine the insulator voltage after 2µs. b) The insulator voltage approaches a constant value after 2 µs. If the basic impulse insulation level (BlL) of the insulator for phase conductor is 150 kV, evaluate the condition of the…
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
The variable resistor Ro in the circuit shown is adjusted until maximum average power is delivered to Ro.1. a) What is the value of Ro in ohms?2. b) Calculate the average power delivered to Ro.3. c) If Ro is replaced with a variable impedance Zo, what is themaximum average power that can be delivered to Zo?4. d) In (c), what percentage of the circuit’s developed power isdelivered to the load Zo?
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
What is the rms value of the applied voltage?? Choose the correct answer.
An alternating voltage given by v = 120 sin (240t + п / 4) V, is applied to a coil withnegligible resistance and inductance of 100 mH. Determine (a) the reactance of thecoil, and (b) the RMS current flowing through the circuit.
For a driven series R⁢L⁢C circuit, the voltage amplitude V0 and frequency f of the voltage generator are 111 V and 211 Hz, respectively. The circuit has resistance R=415Ω, inductance L=0.312 H, and capacitance C=6.23 μF. Determine the average power Pavg dissipated across the resistor.
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.