unacceptable touse in the area of high water groundQ- .........................,level due to high costly of dischargeof ground water during executionand it is made works from normal,non-reinforced concrete.O Wall footing.Foundation is used with bearingwalls system.Footing of several columns locatedon the same axis.O Non of themA single (isolated) footing with twocentral loads of two columns thatare close together.

Q- unacceptable to use in the area of high water ground level due to high costly of discharge of ground water during execution and it is made works from normal, non-reinforced concrete. Wall footing. Foundation is used with bearing walls system. Footing of several columns located on the same axis. O Non of them A single (isolated) footing with two central loads of two columns that are close together.

Q- unacceptable to use in the area of high water ground level due to high costly of discharge of ground water during execution and it is made works from normal, non-reinforced concrete. Wall footing. Foundation is used with bearing walls system. Footing of several columns located on the same axis. O Non of them A single (isolated) footing with two central loads of two columns that are close together.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(3) H 22" IN_ 1:3|2|2|2|3| 4 #8 (b) Check if the #8 bars As, reg 2.85 in ² #4 at 8" 0.c. fé=4.000 psi Grade 60 steel Light weight concrete No-Coating. (a) check if 4 #8 Bars fit the beam. are sufficently anchored (I
Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
Design a RC square footing by Ultimate Strength ACI Column dimensions: 14''x14'' LL= 100 k DL = 71 k qall= 4 ksf f'c = 3 ksi fy = 60 ksi
The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc': 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm diameter bars 350 mm
Please answer asap. Will rate immediately. Thank youuu A slab panel is carrying a superimposed dead load of 2.70 kPa and superimposed live load of 6.0 kPa all over the 4.0m x 18m light storage area. The slab is restrained. The concrete to be used has strength of 28MPa (normal weight). The main reinforcement has yield strength of 350MPa. Use concrete cover of 20mm. The thickness uses a multiple of 10mm. The main reinforcement used us 16mm in diameter. The shrinkage and temperature reinforcement used is 12mm in dia. The unit weight of concrete is 23.6 kN per cubic meter. Using USD, 1. Determine the spacing of 10mm temperature and shrinkage rebar. 2. Determine the ultimate pressure that the slab will carry 3. Determine the spacing of 12mm main rebar at the midspan 4. Determine the spacing of 12mm main rebar at the support.
Calculate the concrete compression force, C., Eq. (4-13b).
Question] Discuss the Plastic hing Length Clp) far this case;- Simply supparted with two cancentratedLead P B. subject: Advanced concrete Design you can use www.cancrete.org-sPIz to find farmatien Deary flease help me te find satution.
(1) (2) 24" (3) 4#7 12" 4#8 12% 4 #9 14" 41 3" 18.5" L 2.5 opening I 2,5" 14" 4" 21" nobuje to 4 3" 3" 4#9 fó= 4000 psi NWC Grade 60 Steel. & Mn = ? fé=3000 psi Grade 60 steel, Tied Bars. &Mn = ? fé= 4ksi. NWC Grade 60 steel, Tied Bars. & Mn = ? 21" NwC 13" fe= 3 ksi Nwc Grade 60 steel & Mn = ?
Design a one-way slab for the inside of a parkily garage. slab thickness 6" f= 4000 psi Gracke bo steel WLL= 180 pst %3D WoL=30 psf Not including the slab self-weignt. NWC.
a w-section is used as a column and is supported by a concrete pedestal as shown. the column will support a service deadload of 450KN and service live load of 650KN. The concrete strength (f'c) = 21 MPa. Determine the dimensions of the baseplate using asd method & NSCP (AISC) specifications. Note: concrete footing dimension 450 x 450 mm -Steel Column Base Plate - Grout -Washer and Thread Concrete Footing- Ancher Rod Shear Lug
Wood planks are used on each working level. The deck width/bearer span is 5 ft.. The bearers and posts are standard pipe and the pipe material is A36 steel with a yield stress of 36,000 psi and modulus of elasticity of 29,000,000 psi. Bearers are to be located at a vertical spacing of 10 ft (largest, lowest post height). Posts are to be 7 ft oc (plank length) parallel to the building wall and 5 ft apart (bearer length) perpendicular to the building wall. There are four working levels and the anticipated scaffold loading will be med duty. A. Assuming the ultimate bending strength of the planks is 3,800 psi (apply a 4:1 F.O.S.), determine the required minimum plank thickness to the nearest 100th. B. Based on the bearer material provided, what is the minimum pipe size that can be safely used? See Appendix 2 in your textbook for steel pipe properties. C. Based on the post material provided, can a 2” standard pipe be used safely? Be sure it satisfies buckling stress conditions only.
C9-1. The concrete footing A was poured when this oolumn was put in place. Later the rest of the foundation stab was poured. Can you explain why the 45° cracks occured at cach corner? Can you think of a better design that would avoid such cracks?