Q.1) For the following space truss where F1 = {300i + 400j -500k}, F2 = {600j}: (a) Find the force in member CB, BE, and BA. (b) State whether each member is in tension or compression. NOTE: Joints A, B, E & F are located in the xy-plane. Similarly, joints C, D, E & F are located in the xz-plane. C F 3 ft B F2 3 ft -4 ft

Q.1) For the following space truss where F1 = {300i + 400j -500k}, F2 = {600j}: (a) Find the force in member CB, BE, and BA. (b) State whether each member is in tension or compression. NOTE: Joints A, B, E & F are located in the xy-plane. Similarly, joints C, D, E & F are located in the xz-plane. C F 3 ft B F2 3 ft -4 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.10P: A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete...

See similar textbooks

Similar questions

A soccer goal is subjected to gravity loads (in the - z direction, w = 73 N/m for DG, BG, and BC; w = 29 N/m for all other members; see figure) and a force F = 200 N applied eccentrically at the mid-height of member DG. Find reactions at sup ports C, D, and H.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
For the truss given below, it is desired to determine the normal efforts that act on the members, so that, thus, possible constraints for its design are possible. Consider that at point A there is a second gender support; and at point D, a first-class support. As this is asked: what is the effort acting on bar AB? Is it guidance or assessment?Source: Hibbeler (2004, p. 588). HIBBELER, R. C. Resistance of Materials. 5. ed. Rio de Janeiro: Technical and Scientific Books Publisher, 2004. Question 1 options: a) A compression force of 100 kN acts on bar AB. B) A tensile effort of 100 kN acts on bar AB. c) A compressive force of 141.42 kN acts on bar AB. d) A compression force of 200 kN acts on bar AB. e) A tensile effort of 141.42 kN acts on bar AB.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
Analyze the Structure given in Figure (Picture Attached) and determine the forces in each member of truss by Methods of Sections. State whether members are in tension or compression. P1= 720KN P2= 360KN
using the method of sections , analyse the truss shown in figure 8 below reguarding forces in menbers ED , DF AND FC .
Consider the truss shown in the figure, built from three struts attached by three pins. The truss supports a downward force of F = 1,250 N applied at the point B. Assume the mass of the truss is negligible, the pins are frictionless, and the supports at A and C are also frictionless. (a) Assuming ?1 = 25.0° and ?2 = 49.0°, what are nA and nC? (Enter the magnitudes in N.) nA= NnC= N (b) The force any strut applies on a pin must be directed along the length of the strut as a force of tension or compression. What are the directions of the forces that the struts exert on the pins joining them? strut AB on joint A: strut AB on joint B: strut BC on joint B: strut BC on joint C: strut AC on joint A: strut AC on joint C: Find the force of tension or of compression (in N) in each of the three struts. bar AB Nbar BC Nbar AC N
Consider the truss shown in the figure. Suppose that F1 = 55 kN and F2 = 30 kN . Determine the force in member ED of the truss, and state if the member is in tension or compression and the force in member EH of the truss, and state if the member is in tension or compression. Determine the force in member GH of the truss, and state if the member is in tension or compression.
The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
For the frame shown in the figure , the axial force in member CD equals *