Answered: Q.1 The full load copper loss of a…

Q.1 The full load copper loss of a transformer is twice its core loss. At what percent of the full load will the efficiency be maximum (A) 25% (B) 50% (C) 70.7% (D) 141%

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Related questions

Q: A short circuit test on 10kva / 2400, 60 hz transformer yields the following result: 4.17 A, 200 V…

A: The solution is given below

Q: The copper loss of a transformer is 100KW. At maximum efficiency, constant losses is less than 100kW…

A: For an electrical machine, efficiency is a very important parameter as If the efficiency is higher…

Q: When a transformer takes a current of 0.8 A and its primary is connected to a 235 V, 50 Hz supply,…

Q: 4.4 A 60HZ, 50KVA, 2400/240 V, single-phase ideal transformer has 50 turns on its secondary winding.…

A: In this question single phase transformer is given....We have to find out primary and secondary…

Q: Current Transformer is used to step up the current of power system. Select one: True

A: Current transformer is a step down transformer. It always step down the current.

Q: Core of the transformer is made-up of material. O Cold Rolled Grain Oriented (CRGO) Silicon Steel O…

A: Core of transformer is made up of... Given I=1.9 Amp, R = 9.5 ohm

Q: losses =los ses 1. Maximum efficiency of transformer is when 2 At maximum effciency load current l2=…

Q: A transformer has a turns ratio of 200:800. If a 0.5 ohm resistor is connected across the secondary,…

Q: An ideal transformer is rated at 15 kVA, 60/240 V. What is the transformer ratio (a = ?) a. 4 b.…

A: Transformer ratio is defined as ration of number of turns of primary winding to number of turns of…

Q: A 400/230V, 50Hz, single phase transformer has 200 turns on high voltage side. Find turns ratio,…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: The efficiency of the transformer is in the range of 80% due to mechanical losses Select one: O True…

A: Need to find true or false

Q: In a 80 KVA, 2000/200 V power transformer, the iron and full load copper losses are 150 W and 400 W…

Q: A 235/ 400 V, 8 KVA, 50HZ single phase transformer has a copper loss of 160 W at full load, unity…

Q: If the full load copper loss of transformer is 251 W, then the copper loss at half load is given by…

A: The solution can be achieved as follows.

Q: A 25 kVA, 550/220 V transformer has a rated copper loss of 350 watts. With the low voltage winding…

A: KVA rating of transformer = 25 KVA Copper losses = 350 watts Applied short circuit…

Q: In a 160 KVA, 2000/200 V power transformer, the iron and full load copper losses are 130 W and 330 W…

A: In this question we will find efficiency of transformer....

Q: If wanting to expand the measurement range of alternating current (AC) by using a current…

A: The transformer turns ratio is given by n1n2=I2I1I2 =n1n2 I1 I2=1160 800 = 5A Answer: 5A…

Q: A 11000/440 V, 50 Hz single phase transformer has a maximum flux density of 1.1weber/m². If the…

Q: Josses = losses 1. Maximum efficiency of transformer is when 2 At maximum efficiency load current…

A: SOLVE PROB.

Q: In a 115 KVA, 2000/200 V power transformer, the iron and full load copper losses are 190 W and 460 W…

Q: 44/ The efficiency is maximum in a transformer when no load losses = Iron losses Select one: True…

A: Need to find true false for given Transformer statement

Q: The Copper and Core losses of a 400 kVA transformer at various loads are as given below: Load (kVA)…

A: Given 400kVA transformer Full load(400kVA) copper losses = 1200W Copper losses at 200kVA loading = ?

Q: 31. The all-day efficiency of a transformer depends primarily on (a) its copper loss (b) the amount…

A: In this question we need to choose a correct option.

Q: Q25. The function of the iron core in the transformer is O providing insulation for the windings O…

A: Transformers need core as they run on magnetism.

Q: A single phase 1.1 KVA, 50 Hz, 220/110 transformer has an Iron losses = 80 W and equivalent…

Q: 2. The ideal transformer has 500 turns on the primary and 300 turns on the secondary. The source…

Q: A transformer having a turn ratio 1:5 and a resistance of 1000 ohms is connected across the…

A: Given data, Turn ratio, NpNs=15 Secondary resistance Rs=1000 Ω

Q: Two 6600/250-V transformers have the following short-circuit characteristics: Applied voltage 200 V,…

Q: . A transformer delivers 650 W to a resistive load. Calculate the primary current if the primary…

A: The detailed solution and formulation is provided below.

Q: Draw the graph of efficiency against load current when the transformer is loaded 12:48 PM

Q: . What are the various causes of voltage drop in atransformer? B. A single phase transformer has…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: A 30KVA, single-phase transformer has core loss of 215 W and Full load Copper loss of 360 W on both…

A: In this question, Find the efficiency of the transformer Efficiency = Po/Pi ×100 Output power Po=…

Q: 391. A transformer has maximum efficiency at load copper loss (P.), is of full load. The ratio of…

A: Given, Transformer maximum efficiency at load factor, x=34.

Q: 1. list the different losses which take place in atransformer. 2. What are the various causes of…

A: Note: Since you have not specified any question to be answered, as per our honor code, we are…

Q: 2.2 An ideal transformer has a turns ratio of 1:5 and is supplied at 200 V when the primary current…

A: Given Turn ratio = N1 / N2 = 1/5 V1 = 200 volt I1 = 3 AMP

Q: In a 75 KVA, 2000/200 V power transformer, the iron and full load copper losses are 80 W and 360 W…

A: In this question, What is efficiency of the transformer and fraction of the load. Efficiency =…

Q: Given |V1| = 30 v. |V2| = shown, what is the magnitude of the primary current, Í,? 90 V, and |Í2| =…

Q: Assertion (A): The regulation of the good transformer should be less than 3 percent. Reason (R):…

A: The percentage difference in the output voltage from no-load to full-load is the transformer's…

Q: A 25-Hz, 120/30 V, 500 VA transformer I to be used on a 60 Hz source. If the core flux density us to…

Q: A 150 KVA transformer has an iron loss of 700W and a full load copper loss of 1800W. Calculate the…

A: Given: S=150 KVAPi=700 W=0.7 KWPcf=1800 W=1.8 KWcosϕ=0.85

Q: 4.14 Given a 3 KVA transformer with an efficiency load and unity power factor and a copper…

A: In this question, We need to determine the iron losses if efficiency of the Transformer is given at…

Q: A transformer with turns-ratio 8:1, has the resistances of the primary and secondary windings as…

Q: 1: 2 100 Ohms 120 V

Q: Calculate the percent voltage drop in a 500 KVA transformer having 2% resistance and 4% reactance…

Q: Q4) Calculate the value of the impedance seen by the source if the step-up transformer turns ratio…

Q: A 50 kVA 2000/200 V transformer has the resistance referred to secondary is 30 Q. The equivalent…

A: resistance referred to primary = secondary referred resistance ×primary voltagesecondary…

Q: 13. A transformer has a turns ratio of 5. If a 100-2 resistor is connected across the secondary,…

A: The turns ratio given in the question is: N1N2=51 The resistance referred to primary can be…

Q: A step-up transformer is 91 percent efficient and has 81 primary turns and 628 secondary turns. If…

Q: A current transformer has a ratio of 100:2. If the secondary has 402 turns what will be the primary…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Q.1 The full load copper loss of a transformer is twice its core loss. At what percent of the
full load will the efficiency be maximum
(A) 25%
(B) 50%
(C) 70.7%
(D) 141%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
In a 130 KVA, 2000/200 V power transformer, the iron and full load copper losses are 80 W and 380 W respectively. Calculate the efficiency at 50 % load and 0.75 power factor. Fraction of Load (X) Efficiency
A short circuit test on 10kva / 2400, 60 hz transformer yields the following result: 4.17 A, 200 V and 218 W. Determine equivalent resistance referred to the high side in ohms (b) determine the equivalent resistance referred to the high side in ohms (c) determine equivalent impedance referred to the high side in ohms(d) determine the percent impedance of the transformer (e) determine the percent voltage regulation at 0.9 leading pf . Subject: electrical apparatus
A single phase transformer is rated at 15KVA, 220/99 , If a load resistance 1.6 ohm is connected across 99 V winding, what is the current in the 220 V winding? (write only the numerical value)
A 200V/20V, 400 VA transformer will be connected as an auto transformer and will be used to convert the 200V input voltage to 220V. In the new situation, how much power (VA) can the transformer nominally supply? A) 800 B) 3600 C) 4400 D) 400 E) 200
A load test for a transformer is run primarily to determine itsA. efficiency.B. copper loss.C. temperature rise.D. resistance loss. Note: I have doubts if it is the letter A or the letter C, can you help me in this question, thanks.
Based on Table Q1 (b), there are experiment for determine thebreakdown strength of transformer oil. Based on the observation,evaluate the breakdown voltage if the gap distance of electrodes is 2.5mm and sketch it in a relevant graph. Gap spacing (mm) 2 3 5 6Breakdown voltage (kV) 50 80 110 130
The primary resistance of a 440/110-V transformer is 0.5 ohms and the secondary resistance is 0.04 ohms. When 440 V is applied to the primary and secondary is left open-circuited, 200 W is drawn from the supply. Find the secondary current which will give maximum efficiency and calculate this efficiency for a load having unity power factor.
A transformer has a turns ratio of 200:800. If a 0.5 ohm resistor is connected across the secondary, what is the resistance in ohms if referred to primary? Group of answer choices 31.25 0.03125 3.125 0.3125