If wanting to expand the measurement range of alternating current (AC) by using a current transformer, set the primary winding current equal to 800A and give the number of turns at the primary winding equal to 1 cycle and the number of turns that Secondary winding equal to 160 cycles, calculate the current at the secondary winding. O 6 A 0 7A 0 5A 8 A

If wanting to expand the measurement range of alternating current (AC) by using a current transformer, set the primary winding current equal to 800A and give the number of turns at the primary winding equal to 1 cycle and the number of turns that Secondary winding equal to 160 cycles, calculate the current at the secondary winding. O 6 A 0 7A 0 5A 8 A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter28: Three-phase Transformers

Section: Chapter Questions

Problem 4RQ: An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral...

See similar textbooks

Similar questions

All values of a transformer are proportional to its __________________ ___________________.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 V, what is the high-leg voltage?
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
The nameplate on a transformer will indicate whether or not it is a Class 2 transformer. (True) (False) (Circle the correct answer.)
Rework Example 3.12 for a+10 tap, providing a 10 increase for the high-voltage winding.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
A 40 kVA, 3300/240, 50 Hz single phase transformer has 660 turns on the primary, Determine: The number of turns on the secondary. The maximum value of the flux in the core. The approximate value of primary and secondary full load currents.
A 100 kVA, 3300/400 V, 50 Hz single phase transformer has 110 turns on the secondary. Determine: i.The number of turns on the primary. ii.The maximum value of the flux in the core. iii.The approximate value of primary and secondary full load currents.
A normal transformer has a nominal 60 kVA. The nominal primary and secondary voltages are 600 V and 120 V respectively. a-) What is the rated current for each winding? b-) If the primary winding is connected to 600 Vac, how many kVA of load can be connected to the secondary?