Q.1 The ultimate tensile strength of the material is 1000 MPa and yield strength of 910 MPa. A rod made of this material which subjected to an axial load of (+170 MPa, -170 MPa). The endurance limit in reversed bending of 0.5 ultimate tensile strength and correction factors as follow; ka= 0.6.5, ksz 0.82, ksur 0.7.6, kf=1.

Q.1 The ultimate tensile strength of the material is 1000 MPa and yield strength of 910 MPa. A rod made of this material which subjected to an axial load of (+170 MPa, -170 MPa). The endurance limit in reversed bending of 0.5 ultimate tensile strength and correction factors as follow; ka= 0.6.5, ksz 0.82, ksur 0.7.6, kf=1.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel specimen in Figure 6.16.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjectedto a tensile load of 1070 kN. The proportional limit of the steel is assumed to be 200 MPa. If thePoisson’s ratio is 0.25, determine the following;a. The transverse strain,b. The total axial deformation, andc. The transverse dimensional change along 300mm.
The interconnected bars were pulled 15.71 mm from the right end and fixed. Bar 1 has a length of 4 m, a cross-section of 1.6 cm^2 and a yield stress of 215 MPa; Bar 2 has a length of 2.9 m, a cross-sectional area of 1.8 cm^2 and a yield stress of 258 MPa^. Since both materials have a modulus of elasticity of 207 GPa and the materials are elastic/perfect plastic:a) What is the plastic elongation of the rod no. 1, in meters?b) What is the elongation of the rod no. 2, in meters?c) How many MPa is the normal stress at the cross section of bar 2?
The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods wereinitially stress-free, what is the largest load P that can be applied without exceeding stresses of 182 MPa in the steel rod and 60 MPa in the bronze rod? D = 0
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
A rigid bar with negligible mass is pinned at O and attached to two vertical rods, figure 1. Assume therods are initially stress-free.a) Solve to determine the maximum load P that can be applied without exceeding stresses of 120MPa in the steel rod, 70 MPa in the aluminum rod and the vertical movement of end C islimited to 5 mm.b) Solve to determine the shearing stress in the pin at O. The pin diameter is 20mm.
A beam of T-section is supported and loaded as shown in the figure. The cross section has width b = 2 1/2 in., height h = 3 in., and thickness t = 1/2 in. Determine the maximum tensile and compressive stresses in the beam Include A. Complete solution B. Free body diagram C. Shear diagram D. Moment diagram
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E=200 GPa. If the allowable stress in rod CD is 120 MPa, what weight W in kgs can be safely applied?
Two planks of different materials are attached by a special glue as shown in the figure. Theplanks have equal widths which is equivalent to 200mm. The thickness of the planks is50mm each. Determine the normal stress acting on the wooden plank and theshearing stress of the glued area if a tensile force of 20kN is applied at both ends.