i need the answer quickly Q.11 An axial pull of 10 kN is gradually applied to a bar of uniform cross sectionalarea 500 mm2 and length 1 m. The modulus of elasticity is 200 GPa. The maximumstrain energy stored per unit volume in the bar isN/m2.

Given; Axial pull = P = 10kN Area = A = 500mm² Length = L = 1m Modulus of elasticity = E = 200GPa

Answered: Q.11 An axial pull of 10 kN is…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plate 0.025mm distant from a fixed plate moves at 60cm/s and requires a force of 2N/sq. m to maintain this speed. Determine the fluid viscosity between the plates.
An 80-kg block rests on a horizontal plane. Find the magnitude of the force P required to give the block an acceleration of 2.5m/s² to the right. The coefficient of kinetic friction between the block and the plane is μk = 0.25.
If the potential energy for a conservative onedegree- of-freedom system is expressed by the relation V = (4x3 - x2 - 3x + 10) ft ⋅ lb, where x is given in feet, determine the equilibrium positions and investigate the stability at each position.
A block of mass m = 1 kg is released from the top of an inclined plane with a height h = 80 cm and a slope of 37 °. The kinetic friction coefficient between the block and the inclined plane is u = 0.3. Find the value (in J) of the work done by the friction force until the block reaches the bottom of the incline.
The jet of a horizontal nozzle strikes a vertical plate with a force equal to 7000N. If the discharge flowing at the nozzle is 0.12 m3/s. Compute the diameter of the jet
Q4 A plate 0.05 mm distant from a fixed plate moves at 1.2 m / s and requires a force of 2.2 N / m² to maintain this speed. Find the viscosity of the fluid between the plates.
A hollow cylinder 1.55m in diameter and 7m long weighs 3,055N. How many cubic meters of metal weighing 105 kN/m3 must be placed inside the cylinder such that 2.6m of the cylinder is protruding above the liquid surface? The hollow cylinder is submerged in a liquid that has a specific gravity of 2.8.
A cube is dropped into the cylinder and the water rises. The length of a side of the cube is 3.7 cm. Specific weight of water is 9.81 kN/m3. Find the density of the cube, the specific gravity of the cube. Where is the vertical CG of the cube? Vertical center of buoyancy based on SWL?
A jet of water whose diameter is 5 cm strikes a fixed cup with a velocity of 9.45 m/s and is deflected by 165o. The jet leaves with a velocity of 30 m/s. If the cup offers a reactive force of 26.5 N to the jet when the flow rate was 980 N/min, determine the ratio of: (a) Actual to theoretical forces of the jet. (b) Velocities at outlet and inlet.
The space between two flat plates of 1 cm in length has been filled with a liquid whose relative density is 0.8. Determine the kinematic viscosity if the force required to displace the 4000 cm ^ 2 top plate at a speed of 20 cm / s is 0.07N.
q3(c) A jet of water (at 10°C) of diameter 2.5 cm flows freely in the atmosphere in a horizontal plane with the initial velocity of 6.5 m/s is deflected by a curved vane 90°. (i) Illustrate the force diagram. (ii) Calculate the forces exerted on the water by the vane in x- and y- direction.
A horizontal force P acts on the top of the 30N block having a width of 25 cm and a height of 50 cm. If the coefficient of friction between the block and the plane is 0.33. What is the value of P for motion to impend?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Q.11 An axial pull of 10 kN is gradually applied to a bar of uniform cross sectional area 500 mm2 and length 1 m. The modulus of elasticity is 200 GPa. The maximum strain energy stored per unit volume in the bar is N/m2.