Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The angle of V is 55° and the load is carried on a swivel head of mean diameter 60 mm . the coefficient of friction between the nut and screw is 0.16 and that between the swivel head and the spindle is 0.1. Calculate the load required to be applied at the end of two levers each of effective length of 500 mm to raise an axial load of 1 KN and the efficiency of the lifting.

Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The angle of V is 55° and the load is carried on a swivel head of mean diameter 60 mm . the coefficient of friction between the nut and screw is 0.16 and that between the swivel head and the spindle is 0.1. Calculate the load required to be applied at the end of two levers each of effective length of 500 mm to raise an axial load of 1 KN and the efficiency of the lifting.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

34 in 3. The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))
Question 3 A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of 34 mm and a pitch of 6 mm is used. The coefficient of friction at the thread and collar are 0.15 and 0.1 respectively. If the collar frictional diameter is 100 mm and the screw turns at a speed of 1 rev/s. (Given dm = 31mm, 1 = 6mm, dc = 100mm). Find: (a) the power input to the screw. (b) the combined efficiency of the screw and collar.
(9) A single thread trapezoidal metric thread has a pitch of 4mm &has a mean diameter of 18mm. It is used as a translation screw in conjunction with the collar having an outside diameter of 37mm & inside diameter of 27mm. Find the required torque in N-m to raise a load of 400kg, if the coefficient of friction is 0.3 for both threads & the collar.
Q1: Power square thread lift 10 tons, dm= 40 mm, do= 46 mm & u=0.15 . choose the thread angle (2) that gives selflocking. Then calculateTR and TL. Neglecting the coller friction.
A bolt with a square threaded screw has mean diameter of 25 mm and a pitch of 3 mm. It carries an axial thrust of 10 kN on the bolt head of 25 mm mean radius. If u = 0.12, find the force required at the end of a spanner 450 mm long, in tightening up the bolt. 3. [Ans. 110.8 N] A turn buckle with right and left hand threads is used to counle twvo railway coaches The threads
The following figure shows a belt brake system operating on a brake drum of the hoisting mechanism. It consists of a cylinder with a diameter of 325 mm, the end of which is the elastic belt connected to both ends of the elastic belt by a crank arm articulated at B and the angle of rotation = 225 degrees. And the coefficient of friction is 0.3 and the latching force is f. Find the necessary F to generate a torque of 350 on the cylinder while it is rotating in the direction shown? Note that s = c = 135mm a = 500mm. 35mm
Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn waste chipper/shredder. As the engine operates at 1200 rpm, the shredding teeth should rotate at 240 rpm. The drive sprocket has 18 teeth. Determine an appropriate pitch for the chain, the number of teeth on the driven sprocket, the pitch diameters of both sprockets, and the chain speed. Also indicate the number of links in a suitable chain and specify the required center distance.
One flange is attached to four 5x8 grade and M16 bolt connections with a total preload force of 80,000 N Calculate the factor of the bolt
QI: A double-threaded 30-mm power screw is 30 mm in diameter with a pitch of 6 mm. The coefficients of friction are 0.05 for the collar and 0.08 for the threads. The frictional diameter of the collar is 40 mm. if Tg=18 N.m: 1- Find the A vertical load on the screw, the torque used to lower the load and screw efficiency. 2- Compute all the stresses on the screw body that will cause by the load.
The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O c. 0.92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is N, Take pressure angle as 14½0. at Pitch P. point Gear driven to 02 The radial force is
Problem: A double-threaded power screw with ISO metric trapezoidal threads is used to raise a load of 300 kN, The nominal diamter is 100 mm & the pitch is 12mm. The coefficient of friction at screw threads is 0.15. Neglect the collor friction. Q.45 Torque required to raise the load is
A single square thread power screw has a lead of 7 mm and mean diameter of 35 mm. If it Is used to lift a load of 30 kN and coefficient of friction of thread is 0.18, find the torque required to turn the screw.