Q.14: For the circuit shown: 1. Draw to scale the total current locus if the RC RL inductor "L" vanied from 0 to 4mH. 2. Find the minimum & maximum total currents V)=100sin(10) supplied to the circuit. 3. Compute the total maximum power factor & maximum consumed power by the circuit. (Ans.: ITmin=89.44A, max=130.384A, p.fmax=0.997 lead, & Pma=6.5KW) VT Xc Xr. ImF wwHH

Q.14: For the circuit shown: 1. Draw to scale the total current locus if the RC RL inductor "L" vanied from 0 to 4mH. 2. Find the minimum & maximum total currents V)=100sin(10) supplied to the circuit. 3. Compute the total maximum power factor & maximum consumed power by the circuit. (Ans.: ITmin=89.44A, max=130.384A, p.fmax=0.997 lead, & Pma=6.5KW) VT Xc Xr. ImF wwHH

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81
Power Electronics. In the Buck-Boost DC-DC converter circuit:Welding voltage [40-80]VSwitching frequency (f) 25khzVoltage between load terminals 55VCapacitance value 470uFLoad current value [10-25]A Under these conditions, which is the lowest ripple (delta IL) amount of the current passing through the coil (L) in Amps for the lowest L inductance value that can keep the DC-DC converter in a continuous current state? A) 23.9803B) 118.75C) 84.3750D) 47.5E) 59.9507F) 33.75
Figure Q1(a) shows a Class A power amplifier circuit. Given the output signal is as shown in the figure, where Vm is the peak voltage and T is the period. For all transistors, you may neglect VBE and VCE(sat) in your calculations. (i) Derive an equation for power conversion efficiency, in terms of Vm, VCC, I and RL. Hence, deduce the maximum power conversion efficiency that is achievable. (ii) Determine the worst-case average power dissipation in each transistor under normal condition (i.e. RL is not open or short)
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
In the Buck - Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: in the voltage range of [AB] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (UF) 5) Load current lload) value: [KS] (Amps) current range The lowest Linductance value that can keep the DC-DC converter in continuous current condition under The lowest ripple (AIL) amount of the current passing through the coil (L) is given below in Amps. Which option do you see? A = 40 Volts B = 80 Volts M = 25kHz F = 55 Volts K = 10 Amps S = 25 Amps
Q.4/ Refer to the class AB power amplifier shown below:a. Determine the dc parameters VB(Q1), VB(Q2), ICQ, VCEQ(Q1), VCEQ(Q2).b. For the 5Vrms input, determine the power delivered to the load resistor.c. Determine the approximate input resistance seen by the signal source if ac=100
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 750 Ω, RB = 100 kΩ, RC = 62 kΩ, and R3 = 100 kΩ. Calculate the voltage gain and input resistance for the amplifier if the BJT Q-point is (40μA, 10 V). Assume βo = 100 and VA = 75V.
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
The ac equivalent circuit for an amplifier is shown. Assume the capacitors have infinite value, RI =750Ω, RB =100 kΩ, RC =100 kΩ, and R3 =100 kΩ. Calculate the input resistance and output resistance for the amplifier if the BJT Q-point is (75 μA, 10 V). Assume βo =100 and VA =75 V.
Q2: (A): What is the advantages and disadvantages of RC coupled amplifier?
In the circuit given in the figure, Vcc = 30V, R1 = 150K ohm, R2 = 47K ohm, RL = 20K ohm and transistor parameters are given as VBE = 0.6 V, beta (dc) = beta (0) = 300. The hybrid model of the transistor will be used.a) It is given as I (CQ) = 2mA and V (CEQ) = 10V at the operating point. Since the input impedance of the circuit must be Zi = 20K ohms, calculate the resistance values of R (E1), R (E2) and R (C).b) Derive the voltage gain expression A (vi) and calculate its value. I sent you question's image. Thank you..