Q.15: The switch has been in position "a" for a long time. At t-0 the switch is moved to position "b". Use classical method to find the voltage across and current through the capacitor as a function of time? (Ans.: Vc(t)=80[1.25-e 20 1000 10mH 30V. 42 100V 2uF S000 (cos5000t+sin5000t)] V & ic(t)=1.6e 500ut sin5000t A)

Q.15: The switch has been in position "a" for a long time. At t-0 the switch is moved to position "b". Use classical method to find the voltage across and current through the capacitor as a function of time? (Ans.: Vc(t)=80[1.25-e 20 1000 10mH 30V. 42 100V 2uF S000 (cos5000t+sin5000t)] V & ic(t)=1.6e 500ut sin5000t A)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume at t=0, a switch in an RC circuit in which the resistor and capacitor are in parallel is closed. how would this affect voltage, charge, and current at t=0 and after a very long time? what if this scenario was the opposite, in which the switch was opened rather than closed? what effect would this have?
Ex : For the circuit shown in the figure below : 1. Find the mathematical expression for the transient behaviour of the voltage across the capacitor as well as the current of the capacitor if the capacitor was initially uncharged and the switch is closed at position 1 when t - o sec . 2. Find the mathematical expression for Vc and is if the switch is moved to position 2 at t = 10msec . 3. Find the mathematical expressions for Vc and ic if the switch is moved to position 3 at t = 20msec 4. Plot the waveforms of the Vc and is obtained from the parts 1 to 3 . R ic 20 kΩ 20 E 12 V C 0.05 uF vc R , 310 ΚΩ T
The response of an electrical circuit is modeled by the function v(t) =5-3e ^ -t/10 , where “V” represents the output voltage in Volts and “t” is the time is milliseconds after the circuit is turned on. a) Determine the output voltage at the instant the circuit is turned on ( t = 0). b) Determine the time at which the output voltage will reach 4 Volts. c) Sketch the graph of the voltage function for t>0. Show the asymptote and the vertical intercept. d) determine an equation of a rational function that has the following characteristics. a horizontal asymptote defined by y = 1 a vertical asymptote defined by x = − 2 a zero x = 4
Q5. For an exhibition project you are designing a circuit of signal processor which can be connected to 230V, 50 Hz supply have a 5.0 H inductor, 80 μ F capacitor and 40Ω resistor kept in series. How can you evaluate the rms current and average power delivered to the circuit? Based on your observation, evaluate the potential drop across capacitance and inductor. Comment about that r m s voltage found in this circuit is less than peak voltage? Justify it with your answer. If you remove the inductor and connect a bulb in series with a capacitor. What will happen to the brightness of bulb if it is connected to DC source and then to an AC source. Assess and find reason for your observations in each case.
Differential equation electrical circuit please answer asappp. For Part c mention the units the answer is in
Please upload a simulation in matlab based off the equation for the attenuation constant. Needs Complete solution with 100 % accuracy.
For the circuit in the figure, initially the switch S is closed in (b), until the capacitor is charged; then the switch goes to point (a) so that the battery is disconnected and the capacitor, resistor and inductor are connected in series. Once S is connected at point (a), find a) the angular frequency of oscillation for the series circuit b) write the equation for the charge on the capacitor as a function of time with the respective values of Qmax, angular frequency Wd and time T c) make the Q(t) graph showing explicitly the envelope of the exponential decay (Hint: use geogebra or an application of your choice to obtain a graph).
What is the input to the system with specification given, Kp = 10, 500? A. Step function B. Ramp Function C. Parabolic Function
Given circuit, capacitor voltage is at 0 V with switch SW1 open. At time t0, switch SW1 is closed. At time t0, what is the voltage v? What is the voltage v at time infinity? At time t0, what is the current through R2? What is the current through R2 at time infinity?
The Nyquist plot that has semicircles and the straight lines is commonly used to estimateimpedances at various stages of the electrochemical devices. For some devices thesemicircles are not perfect semicircle but are somewhat open as shown below. What is thereason for it?
The pathway for a binary electrical signal between gates in an integrated circuit can be modeled as an RC circuit, as shown in the figure to the right; the voltage source models the transmitting gate, and the capacitor models the receiving gate. Suppose the resistance is 500 ohms and the capacitance is 10^-12 F (1 picofarad, pF. If the capacitor is initially uncharged and the transmitting gate changes instantaneously from 0 to 6 V, how long will it take for the voltage at the receiving gate to reach 5 V?
Which of the following is true regarding the behavior of capacitors when energized by a DC source? a. At transient state, the capacitor behaves as an open circuit. b. At transient state, the capacitor behaves as a short circuit. c. At steady-state, the capacitor behaves as a short circuit. d. At steady-state, the capacitor behaves as an open circuit.