Part 2:Two voltages V,= 8coswt and V, =5sinwt are inputs to an analogue circuit.a) Determine an expression for the output voltage if this is given by (V, +V2) in the formR sin(wt + a).b) Sketch the graphs of V,, V, and (V, +V2) on the same axis by,i)Combining the sine waves graphicallyii)Using the result that you have obtained in a).c) Compare your results in b).You should explain the variation between the two methodscomparing the two methods you have used.

Two voltages V1=8cosωt and V2=5sinωt are inputs to an analogue circuit. a) We need to determine an…

Part 2: Two voltages V,= 8coswt and V, =5sinwt are inputs to an analogue circuit. a) Determine an expression for the output voltage if this is given by (V, +V½) in the form R sin(wt + a). b) Sketch the graphs of V,, V, and (V, +v,) on the same axis by, i) Combining the sine waves graphically ii) Using the result that you have obtained in a). c) Compare your results in b). You should explain the variation between the two methods comparing the two methods you have used.

Part 2: Two voltages V,= 8coswt and V, =5sinwt are inputs to an analogue circuit. a) Determine an expression for the output voltage if this is given by (V, +V½) in the form R sin(wt + a). b) Sketch the graphs of V,, V, and (V, +v,) on the same axis by, i) Combining the sine waves graphically ii) Using the result that you have obtained in a). c) Compare your results in b). You should explain the variation between the two methods comparing the two methods you have used.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Mcq Q1) What is the benefit of using two pulse transformers to drive the SCR of a single-phase bidirectional AC voltage controller? * - to isolate the SCRs from the source - to isolate the SCRs from getting short - to isolate the load from the source to control the rms output voltage
What is the value of the excitation current(If)?
Sketch the AM modulated signal (assume sinusoidal signal modulating a sinusoidal carrier) in both time and frequency domain. Remember, graphs with missing labels and values will be graded with zero.
When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.
Sketch a phasor diagram showing Vin, Vout, Vr, Vc. What would be the phase shift for a dc input, and very high frequency input?
Determine and sketch the output voltage waveform for the circuit shown if the sinusoidal signal at the input has a peak-to-peak voltage of 30 volts with V=5volts. Identify the circuit.
Residential AC voltage for many European countries is 230 VRMS at 50 Hz. Calculate the following quantities for the AC signal: peak voltage, VP (in V); peak-to-peak voltage, VPP (in V); and period, T (in ms).
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
Consider the following equation: v (t) = 110 sin(78.5 t) Calculate: Frequency (f) = ? Time period (T) = ? Peak Voltage (Vp) = ? Average voltage (VAVG) = ? RMS voltage (VRMS) = ? Sketch the labelled waveform showing Peak voltage, full cycle and half-cycle times.
Evaluate the following Williamson's factor: W84
c) If we consider the resistor, capacitor and inductor as the load connected to the twovoltage sources, at which frequency can the load be considered resistive (two decimalaccuracy required)? d) If we consider the resistor, capacitor and inductor as the load connected to the twovoltage sources, at which range of frequencies can the load be considered inductive(two decimal accuracy required)?
The graph of the vs sign applied to the circuit in the figure is given above. The switch works ideally in the circuit Switch; When the applied input signal is positive, it becomes closed. Current flows through it) In the applied input signal, Vp = 12V, R = 10ohm, T = lms. According to this; a) Find the mean and rms values of the output voltage? b) Find the average input power and output power and calculate its efficiency. c) If we consider that there is a voltage drop of 1V on the switch; c.1) Calculate the average and rms values of the output voltage, c.2) Average input power and output power c.3) Efficiency.