Q.2: For the following signal: x(t) = 10 sin (2n x 10³t + 30°) answer the following questions: 1 * :The signal is Energy Signal O Power Signal O The normalized energy of this signal 2 * (is equal to: (please write a number zero infinity none of the mentioned answers 3 The normalized power of this signal (is equal to: (please write a number

Q.2: For the following signal: x(t) = 10 sin (2n x 10³t + 30°) answer the following questions: 1 * :The signal is Energy Signal O Power Signal O The normalized energy of this signal 2 * (is equal to: (please write a number zero infinity none of the mentioned answers 3 The normalized power of this signal (is equal to: (please write a number

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Similar questions

A resistor of 100 Ω, a coil of 4.50 μH, and a capacitor of 220 pF are in parallel. What is the admittance vector at 6.50 MHz? Provide illustration of the circuit.
Q5. For an exhibition project you are designing a circuit of signal processor which can be connected to 230V, 50 Hz supply have a 5.0 H inductor, 80 μ F capacitor and 40Ω resistor kept in series. How can you evaluate the rms current and average power delivered to the circuit? Based on your observation, evaluate the potential drop across capacitance and inductor. Comment about that r m s voltage found in this circuit is less than peak voltage? Justify it with your answer. If you remove the inductor and connect a bulb in series with a capacitor. What will happen to the brightness of bulb if it is connected to DC source and then to an AC source. Assess and find reason for your observations in each case.
POWER SİSTEMS high voltage technique it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approximate impulse,AC AND DC voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE SAME QUESTION FOR DC HİGH VOLTAGE AND AC HİGH VOLTAGE WHAT THE DIFFERENCE BETWEEN THEM
In an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz, respectively, an R = 500Ω, L = 0.20 H, and C = 2.0μF. (a) What is the impedance of the circuit? (b) What is the amplitude of the current from the source? (c) If the emf of the source is given by v(t) = (100 V) sin 1000πt , how does the current vary with time? (d) Repeat the calculations with C changed to 0.20μF.
Please answer fast A circuit is operated at its resonant frequency, which is designed to be 240 Hz. The circuit contains a toroid that provides an inductance of 370 mH, and has a total resistive load of 1250 Ohms. Due to the passage of time, eventually the frequency decreases to 220 Hz. If when operating under design conditions it used an average power of 440 W, find: a) The capacitance of the circuit. b) The peak and rms current and voltage at which it operates under design conditions. c) The peak and rms current and voltage at which it operates under conditions after heavy use. d) The power factor in the condition after much use.
A series RLC circuit has an inductor that has a value 500 mH, the capacitor 25 µF, and the resistor has a value of 400 Ω. They are connected to an ac power supply functioning at frequency 60 Hz. The peak current is 450 mA a) Find Vmax b) Find the angle by which the current leads, or lags, the voltage. Using your result is it leading or lagging? c) How much power is the circuit dissipating on average?
A LC circuit in a radio tuned to 1080 kHz has an inductor with an inductance value of 60 μH and a resistance of 0.25 Ω. a. what is the capacitance of the LC circuit? b. sketch the impedance phasor diagram for the radio. Be sure to label important features of the diagram.
An exponential signal has initial value Vi=v(0)=-3[V], final value Vf=(∞)=6[V], and a time constant of 10s. Determine: a) the equation for v(t) b) Graph the function for 0≤t≤100 sec, together with a table of values at 10s (or less) time intervals.
A 200 Ω resistor, 0.900 H inductor, and 6.00 µF capacitor are connected in series across a voltage source that has voltage amplitude 30.0 V and an angular frequency of 250 rad/s. (a) What are v, vR, vL, and vC at t = 20.0 ms? Compare vR + vL + vC to v at this instant. (b) What are VR, VL, and VC? Compare V to VR + VL + VC. Explain why these two quantities are not equal.
The terminal points determined by pi/2, pi, -pi/2, 2pi are __________, ________, ___________, and ___________, respectively.
37. "Mathematically, out of phase means that the phase angle of two waves are the different and its phase difference is zero." True False "In time domain represenatation of a signal, a signal with an expression of 220 sin (377t -180) is also equal to -220 sin (377t)." True False "Phasor domain representation is an ac signal representation considers the time-varying nature of the signal, specifically its sinusoidal form." True False In time domain represenatation of a signal, a signal with an expression of 220 sin (377t -90) is also equal to +220 cos (377t)." True False
What is incorrect about the RLC AC Circuit shown? 1 The power dissipation through the (ideal) capacitor is vanishing. 2 The current leads the voltage across the capacitor by 90deg. 3 The voltage across the inductor leads the current by 90deg. 4 If the AC source is replaced by a constant DC source, after a very longtime, the voltage across the inductor vanishes. 5 If the AC source is replaced by a constant DC source, after a very longtime, the voltage across the capacitor will be equal to that across theresistor.