QI: In an industry a general-purpose visual equipment displays an alternating waveform comprising of following data, i(t) =75 sin (200xt) volts. Validate the normal AC parameters for the given equation. If you decide to have a phase shift of 14.32 degrees in radians, what would be the new equation? Justify with the valid facts how same industry uses certain recommendable characteristics to construct thermopile.

QI: In an industry a general-purpose visual equipment displays an alternating waveform comprising of following data, i(t) =75 sin (200xt) volts. Validate the normal AC parameters for the given equation. If you decide to have a phase shift of 14.32 degrees in radians, what would be the new equation? Justify with the valid facts how same industry uses certain recommendable characteristics to construct thermopile.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Similar questions

6.22 Let v1 ¼ 8 sin 100t and v2 ¼ 6 sin 99t. Show that v ¼ v1 þ v2 is periodic. Find the period, and the maximum, average, and effective values of v. Ans: T ¼ 2; Vmax ¼ 14; Vavg ¼ 0; Veff ¼ 5 ffiffiffi 2 p 6.23 Find period, frequency, phase angle in degrees, and maximum, minimum, average, and effective values of vðtÞ ¼ 2 þ 6 cosð10t þ =6Þ. Ans: T ¼ 0:2 s; f ¼ 5 Hz; phase ¼ 308; Vmax ¼ 8; Vmin ¼ 4; Vavg ¼ 2; Veff ¼ ffiffiffiffiffi 22
A coil has a resistance of 50 ohms and an inductance of 0.5 Henry. What is the RMS value of current flowing in the coil if the supply voltage is Vt = 500sin377t.
A 400 Hz sinusoidal voltage with a maximum amplitude of 100 Vat t=0 is applied across the terminals of an inductor. The maximumamplitude of the steady-state current in the inductor is 20 A.1. What is the frequency of the inductor current?2. If the phase angle of the voltage is zero, what is the phase angle ofthe current?3. What is the inductive reactance of the inductor?4. What is the inductance of the inductor in millihenrys?5. What is the impedance of the inductor?
Calculate the velocity factor of a coaxial cable used as a transmission line with the characteristic impedance of 50 ohms; capacitance is 40 pF/m and an inductance equal to 50 microH/m.
The voltage (in Volts) across an element is given as v(t) = 50 cos (6ft + 21°) whereas the current (in Amps) through the element is i(t) = -20 sin (6ft +46.1°); where time, t is the time and f is the frequency in seconds and Hertz respectively. Determine the phase angle between the two harmonic functions.
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage V and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60 Hz, R = 10 R. Vcoil = 22.4 V, VR= 20 V and V = 36 V. find the resistance and inductance of the coil. please use reference photo
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.
The voltage (in Volts) across an element is given as v(t)= 50 cos(6ft +24.7°) whereas the current (in Amps) though the element is i(t) = - 20 sin(6ft +55°); where time, t is the time and f is the frequency in seconds and Hertz respectively. Determine the phase angle between the two harmonic functions
characteristic impedance z0 = 50 ohms is a short-circuited coaxial (coaxial) cable with a length d = 0.3λ component is wanted to be made. Use Its frequency is f = 8 GHz. (a) Identify the component. (b) Find the impedance value of the component. (c) Find the parameter value of the component. lesson:electrical and electronical engineering
b) Find the rms current flowing in an AC capacitive circuit when a 4μF capacitor is connected across a 880V, 60Hz supply.
Consider a 760 W light bulb that requires an RMS voltage 21 V to operate normally. How large should an inductance be connected in series with the bulb if the combination is connected across a RMS voltage 255 V, 71 Hz line? (You may neglect the resistance of the inductor and the inductance of the light bulb.)
An audio power amplifier delivers a 30 volt RMS 1 kHz sine to a loudspeaker. If the loudspeaker impedance at this frequency is 7 at 45°, determine the RMS current delivered to the load and the true power.