Q.2 – In the diode circuit Va-24,7, Vb=-15,3, Vr-9,5 , R1-945 and R2=1500 are given in Appendix.2. Assuming the clipper circuit uses a şilicium diode (VD = 0,7 V) in figure. Determine voltage range of diode ON- OFF situation and find the values of the circuit a) for Vi = Va; In . I2 , VR1 , Vo and Ppiode b) for Vi = Vb; In , I2 , VR1 , Vo and PR2 Vị (V) Vaf Is R1 + Vr1 - ID I2 D Vị Vo R2 VT Vb+ Q+ +

Q.2 – In the diode circuit Va-24,7, Vb=-15,3, Vr-9,5 , R1-945 and R2=1500 are given in Appendix.2. Assuming the clipper circuit uses a şilicium diode (VD = 0,7 V) in figure. Determine voltage range of diode ON- OFF situation and find the values of the circuit a) for Vi = Va; In . I2 , VR1 , Vo and Ppiode b) for Vi = Vb; In , I2 , VR1 , Vo and PR2 Vị (V) Vaf Is R1 + Vr1 - ID I2 D Vị Vo R2 VT Vb+ Q+ +

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
Consider the circuit below,assuming the diode is ideal:1) When voltage source (Vin) provides a positive voltage, the diode isequivalent to ____________ circuit2) When voltage source (Vin) provides a negative voltage, the diode isequivalent to ____________ circuit3) Sketch the I-V characteristic of the ideal diode model on the chart below.
⦁ Consider the below zener diode circuit and find the values of , , , . Use the constant voltage drop model which is shown is Figure 2. Show your solution steps clearly and explain them. The answers without solution steps will not be graded. Also, state your results in the sections below the circuits. ( = 0.1 )
In the circuit, diode D1 has n = 1.4 and has an operating point I D = 1mA at V D =0.7 V and is at room temperature. Diode D2 has an area that is 20 times larger than D1 but isotherwise the same. a) What is the current through diode D1?b) What is the value of the saturation current, Is for diode D2?c) What is the voltage Vx ? d) Determine the value of R to make Vo = -0.2V
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
Please answer in short I will like but please asap please urgent... Consider the circuit shown in the figure. Assume that each diode has a turn-on voltage of V_gamma = 0.6V. a) Determine R1, R2 and R3 such that, ID1 = 0.2mA, ID2 = 0.3mA and ID3 = 0.5mA. b) Find the voltage across V1, V2 and the current for each of the diodes for, R1 = 10kΩ, R2 = 4kΩ and R3 = 2.2kΩ.
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
accepting that D1 and D2 diodes have the same properties in the circuit given in the figurea) output voltage, b) current flowing through the resistor,c) current flowing from diodes calculate.
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
Q1: In this Zener diode regulator, the source voltage varies from 6 V to 14 V. Assume that the load current varies between 1 mA and 35 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Q2: Given the circuit design for a Zener diode regulator in the Ques 1, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.