2.46 The diodes in the circuit in Figure P2.46 have the same piecewise linearparameters as described in Problem 2.44. Determine the output voltage Voand the currents Ipı, Im2, Ipa, and / for the following input conditions: (a)V = V2 = 0; (b) Vi = V2 = 5 V; (c) V = 5 V, V2 0; and (d) V 5 V,V2 = 2 V.%3D+10 V0.5 k2Da9,5 k2Voww本oVo0.5 k2D2V20 ww本Inst+5 VFigure P2.46

a) Refer to Figure P2.46 in the textbook. The voltages are, The cut-in voltage for each diode is, .…

2.46 The diodes in the circuit in Figure P2.46 have the same piecewise linear parameters as described in Problem 2.44. Determine the output voltage Vo and the currents Ip1, Ip2, Ip3, and / for the following input conditions: (a) V = V2 0; (b) V = V2 = 5 V; (c) V =5 V, V2 0; and (d) V 5 V, V2 = 2 V. %3D %3D %3D +10 V 0.5 kf2 D 9,5 k2 Voww 本 OVo 0.5 k2 D2 V20 ww 本 AD, Ips +5 V Figure P2.46

2.46 The diodes in the circuit in Figure P2.46 have the same piecewise linear parameters as described in Problem 2.44. Determine the output voltage Vo and the currents Ip1, Ip2, Ip3, and / for the following input conditions: (a) V = V2 0; (b) V = V2 = 5 V; (c) V =5 V, V2 0; and (d) V 5 V, V2 = 2 V. %3D %3D %3D +10 V 0.5 kf2 D 9,5 k2 Voww 本 OVo 0.5 k2 D2 V20 ww 本 AD, Ips +5 V Figure P2.46

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

For the circuit shown in Figure 2-a, plot the output voltage across the resistance R, using the diode characteristic presented in Figure 2-b. Assume the input AC voltage supply given by Vs = 1. sin(2pifot). Where fo = 100 Hz. In addition, could you suggest a method on how to keep the output voltage more constant.
diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
Redraw the circuit and determine the value of ID and VO for the diode configurationshown in Figure Q2a.
Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
Question: The circuit in Figure P2.14 is a complementary output rectifier. If vs = 26 sin [2?(60)t]V, sketc... The circuit in Figure is a complementary output rectifier. If vs = 26√2sin[120πt]V,sketch the output waveforms vo+ and vo? assumingV? =0.6V for each diode. And explain the operation of the circuit.
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
In the circuit shown in Figure 2–52 (p. 97), the Zener diode has a reverse breakdown voltage of 12V. RS = 50 Ohms, VS = 20V, and RL can vary from 100 Ohms to 200 Ohms. Assuming that the Zener diode remains in breakdown, find: (a) the minimum and maximum current in the Zener diode; (b) the minimum and maximum power dissipated in the diode; and (c) the minimum rated power dissipation that RS should have.
Q2 (b) Multiple diodes circuit is given in Figure (i) Identify the condition for Si and Ge diodes. (ii) Determine the current flowing into Si and Ge diodes. (iii) Calculate the output voltage, Vo
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
accepting that D1 and D2 diodes have the same properties in the circuit given in the figurea) output voltage, b) current flowing through the resistor,c) current flowing from diodes calculate.