Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg P. = 500 kPa T = 500°C Po = 0 kPa D= 0.02m

Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg P. = 500 kPa T = 500°C Po = 0 kPa D= 0.02m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air with stagnation pressure of 800 kPa and temperature of 100⁰C ,is expanded isentropically to the channel 1 where A₁ = 20 cm² and P₁ 47 kPa. Count: a. Ma1 b. The area of the throat / neck (the narrow part) of the channel c. Mass flow rate m d. In part 2 which is located between the throat/neck with part 1, where the area of part 2 is 9 cm² ,calculate Ma2
Air enters a converging- diverging nozzle at a pressure of 830 kPa abs and a temperature of 32°C. Neglecting the entrance velocity and assuming a frictionless process, find the Mach number at the cross-section where the pressure is 240 kPa abs.( for air: k = 1.4 R=287J/kgK)
Each stage of an axial flow compressor is of 0.5 reaction, has the same mean blade speed and the same flow outlet angle of 30 degree relative to the blades. The mean flow coefficient is constant for all stages at 0.5. At entry to the first stage the stagnation temperature is 278 K, the stagnation pressure 101.3 kPa, the static pressure is 87.3 kPa and the flow area 0.372 m. Using compressible flow analysis determine the axial velocity and the mass flow rate.
A convergent-divergent nozzle with an exit-to-throat area ratio of 1.616has exit and reservoir pressures equal to 0.947 and 1.0 atm, respectively.Assuming isentropic flow through the nozzle, calculate the Mach numberand pressure at the throat.
The converging-diverging nozzle of the engine of a new supersonic unmanned aerial vehicle (UAV) has an exit area of 50 cm^2 . At the design operating condition, the mass flow rate of exhaust gases (? ≈ 1.4, molecular weight = 26 g/mol) is 1.75 kg/s. The exhaust gases enter the nozzle with stagnation pressure and temperature equal to Po = 300 kPa and To = 500 K, respectively a) What is the optimal cruising altitude for the operation of the nozzle of this UAV? (b) What is the lowest altitude at which the plane can fly such that the flow inside the diverging part of the nozzle is kept supersonic? Note: - Assume that the stagnation conditions of the flow of exhaust gases entering the nozzle are kept constant with varying altitude
Air flows in a converging-diverging nozzle with an exit Mach number of 1.8 . The nozzle is supplied from an air reservoir at 8MPa. Assuming one-dimensional flow, the maximum back pressure to choke the nozzle is _______.
An aircraft flies with a Mach number Ma1=0.962 at an altitude of 7062 m where the pressure is 46.2 kPa and the temperature is 246.2 K. Calculate the stagnation properties (static temperature, pressure, density), cross-section areas A1 and A2=? at the inlet and outlet of the diffuser. The diffuser at the engine inlet has an exit Mach number of Ma2=0.3. For a mass flow rate of 36,2 kg/s, determine the static pressure rise across the diffuser and the exit area. Solve the problem by making the necessary assumptions and drawing the schematic figure.
The converging-diverging flow domain is shown in Figure 1. The inlet diameter is 0.2 m, the throat diameter is 0.15 m, and the outlet diameter is 0.24 m. The axial distance from the inlet to the throat is 0.30 m—the same as the axial distance from the throat to the outlet. At the inlet section, the stagnation pressure P0 is set to 220 kPa (absolute), while the stagnation temperature T0, at the inlet is set to 300 K.
The stagnation pressure after the normal shock wave in a diverging nozzle (pi= 170 kPa, Mi= 2.4, Ax ⁄ Ai = 2.0)
How do I find reservoir pressure given the exit-to-throat area ratio of a supersonic nozzle and a Pitot tube measurement from the test section.
A gas at a specified stagnation temperature and pressure is accelerated to Ma = 2 in a converging–diverging nozzle and to Ma = 3 in another nozzle. What can you say about the pressures at the throats of these two nozzles
A converging–diverging nozzle with a 4:1 exit-area ratioand p0 = 500 kPa operates in an underexpanded condition as in Fig. The receiver pressureis pa = 10 kPa, which is less than the exit pressure sothat expansion waves form outside the exit. For the givenconditions, what will the Mach number Ma2 and the angleϕ of the edge of the jet be? Assume k = 1.4 as usual.