Q.3 A flat plate of width 60mm has a central hole of 10mm diameter. This plate is subjected to an axial load of PKN (tensile). Determine the thickness of plate if o,„=300Mpa for plate material and FOS=3. Take P as 5KN, 6KN, 7KN, 8KN, 9KN, 11KN.

Q.3 A flat plate of width 60mm has a central hole of 10mm diameter. This plate is subjected to an axial load of PKN (tensile). Determine the thickness of plate if o,„=300Mpa for plate material and FOS=3. Take P as 5KN, 6KN, 7KN, 8KN, 9KN, 11KN.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Related questions

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

Q: Two solid cylindrical rods support a load of P = 27 kN as shown. Rod (1) has a diameter of 17 mm,…

Q: he rigid bar AB with a length of 5m, is attached to two vertical rods and is horizontal before the…

A: Given

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

Q: The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3.…

Q: А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN…

A: In compression, we examined a cube with a 2.5 cm edge, as illustrated in the picture. It failed…

Q: Let's load a 1500 kg load on a platform with its own weight of 500 kg as shown in the figure. This…

A: Given data: Mass of the load, mL = 1500 kg. Mass of the platform, mp = 500 kg. The number of rods,…

Q: A hanger rod is stressed to 0.9167 N/mm2 , when a tensile load of 18 N is acting on it as shown in…

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: Bar width, w= 2.25 in Bar thickness, t= 0.375 in Pin diameter, d= 0.775 in Applied load, P= 4800 lb…

Q: applied Q2: A (500*400) mm column shown in Fig.2 is reinforced with 12 32mm bars. service dead load…

A: Given Datab=500mmd=400mmAst=12-ϕ32mmfc=25MPafy=400MPa

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

A: Option d is correct.

Q: Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm…

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di = 37.5 Allowable stress of rod : σ=…

Q: The assembly shown in Figure consists of an aluminum tube AB having a cross-sectional area of 400…

Q: Two are connected by a knuckle jont, as shown in Fig by a pin of 40 mm in diameter. If a pull of 120…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…

Q: 100 kN lsize as sho 80 [A find the diameter of the rivet. 18. A bracket in the form of a plate is…

A: Given Load= 100 kN Maximum shear stress = 70 MPa Cursing stress = 100 MPa To find Diameter…

Q: A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead…

A: Given data, Side of the square plate, a = 2 m Diameter of the steel rod, d = 6 mm Surface load of…

Q: A 12 mm thick steel plate with five 25 mm hole is under a tension load as shown in Fig. 2. Assume…

Q: 1. Three vertical rods AB, CD, and EF supports s load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: 5. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if…

A: Given data: F=5 kNσ=100 N/mm2 Need to determine the minimum required diameter of the wire.

Q: 2.49. A bar of rectangular cross section 20 mm x 3 mm has a central hole of diameter 6 mm. Find the…

Q: 1. Problem Solving. Woite inside a Box. 1) Find the alliwable safe load p if the stresser in the bar…

A: Stress in bar AB, σAB=60ksi=413.685N/mm2Stress in bar BC, σBC=50ksi=344.738N/mm2Stress in bar CD,…

Q: A 12 mm thick steel plate with five 25 mm hole is under a tension load as shown in Fig. 2. Assume…

A: Given: A steel plate is subjected to a tensile axial load of Nt,rd. Thickness of plate, t = 12 mm…

Q: The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than…

Q: The stress concentration occurs whenever there is an abrupt change in the cross-section of a…

A: Stress concentration Factor (k) : it is defined as the localisation of higher stresses due to…

Q: answer as soon as possible

A: The eccentric load is acting on the cube. Due to this, there will two types of stress generated…

Q: 1. Three vertical rods AB, CD, and EF supports a load of 36 kN. Each of the rods AB und CD has a 200…

A: When an external force is applied to any body, the body gets deformed. This deformation is resisted…

Q: Figure 1 shows a rigid pipe being supported by a pin at A and a steel wire BD. The BD wire has a…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: 2 A hollow circular steel strut with its ends position- fixed, has a length of 3 m, external…

A: We know that a 3 m long hollow circular steel strut with fixed ends has an exterior diameter of 12.5…

Q: Find the Young's Modulus of a brass rod of diameter 25 mm and of length 250 mm which is subjected to…

A: Given, Diameter of rod = d = 25 mm Length of rod = L = 250 mm Tensile load = P = 50 kN = 50 x 103 N…

Q: Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 KN tensile load if the…

Q: load of F=1433 kgf will be hung on a Workshop crane as in the figure. The pole to be used has a…

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

Q: 1. Three vertical rods AB, CD, and EF supports a load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Q1/ The bar shown in Fig. 1 is subjected to a tensile load of 50 KN. Find the diameter of the middle…

Q: C. For the figure shown below, if the stress in steel and bronze are not exceeding 150MPA and 70MPA…

Q: 2. A steel bar that is 5.75 m long must support a tensile load of P = 20 kN without stretching more…

Q: Q.1. A. For a hellow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: 1) Given: Outside diameter D2=138mm Inside diameter D1=120mm Maximum tensile stress=115MN/m2 or…

Q: given plate below with width of 200 mm and thickness of 16 mm is to be connected to two plates of…

Q: A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensile force of 200…

A: GIVEN DATA- SIDE OF SQUARE a=50mm L=250mm E=200GPa P=200KN POISSON RATIO=0.3 WE HAVE TO FIND…

Q: b) A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If…

Q: subjected to uniform uniaxial tension of 95 MPa. A large uniform plate containing a rivet hole is…

Q: A crane hook shown in figure below is made of 30 mm diameter steel rod. The distance between the…

A: To find: The load F so that the maximum stress in the rod is not exceed 40 Nmm2. Given: The diameter…

Q: Q1A 30 cm square steel bearing plate lies between a 20 cm diameter wooden post and a concrete…

A: According to the given information:…

Q: PROBLEM 1 Determine the load that can be applied at the end of the rigid bar if the stress in either…

Q: Q.1: Ifa material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength -…

A: Data given- Ultimate tensile strength = 300 MPa Ultimate compressive strength = 900 Mpa

Q: 2.49. A bar of rectangular cross section 20 mm × 3 mm has a central hole of diameter 6 mm. Find the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Q2- The homogeneous bar AB have diameters ubjected to an axial tensile load of 25KN. have he new…

A: SOM Note: Working stress should be 0.25 N/mm2

Q: The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the…

A: The axial force is the rod's compression or tension force. The maximum load, places the rod in an…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

100%

Q.3 A flat plate of width 60mm has a central hole of 10mm diameter. This plate is subjected
to an axial load of PKN (tensile). Determine the thickness of plate if o,-300Mpa for plate
material and FOS=3. Take P as 5KN, 6KN, 7KN, 8KN, 9KN, 11KN.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?