Q.4/ Determine the magnitude of distributed force 5 KN/m and its location on the beam as shown. * SkN/m 4 m 6m

Q: The speed of your automobile has a huge effect on fuel consumption. Traveling at 65 miles per hour (...

A: The speed is defined as the ratio distance to the time period, which means speed is the distance cov...

Q: 90 MPa 60 MPa 20 MPa

A: Given, Normal stress in x-direction = σx = -20 MPa Normal stress in y-direction = σy = 90 MPa Shear ...

Q: In the figure shown: Pk is the same for point A and B. What is the acceleration(m/s?) of the block i...

A:

Q: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a comp...

A: Given:P=750 KNσ=55 MPado=25 cm

Q: Solve the problems on a clean sheet of paper. Follow the Given-Required-Analysis-Solution-Summary of...

A:

Q: A 30 mm diameter shaft transmits 10 kW at 600 rpm. It was found that a stress raiser exist whose str...

A: The given values are -  P= 10 kW, d= 30mm, N = 600rpm, τsy=150 MPa Let T be the twisting moment.

Q: al stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.

A:

Q: You are using a 10 mm thick and 25 mm wide, steel plate with a central hole of 5 mm subjected to a t...

A: Givent=10mmD=25mmd=5mPmin=5kNPmax=25kNreliability =98%cold drawn 

Q: Determine the internal forces at point K when a semicircular rod is loaded.

A:

Q: Identify what is the system in this problem and write the general energy balance equation (no need t...

A:

Q: would find the velocity of each point (no values given just the equation) for an overlapping/superim...

A:

Q: Determine the value of the extrusion pressure (P/o) for the manufacture of a bar with a square secti...

A:

Q: le value of the clamping for stress in the 5-mm diameter ssible value of the applied loa ntained?

A:

Q: A device's outer cylinder diameter is 7" and its distance from outer cylinder to the inner cylinder ...

A:

Q: O ) Listen Q3. Two blocks, A and B, are connected using the cable and pulley system as shown. (The c...

A:

Q: gid vessel. At v rature will the the container

A:

Q: For Hibiscus and Rose Groups A steel helical spring is wound from No. 14 music wire with a mean heli...

A:

Q: total drill time in seconds is

A: Given data; In a single pass drilling operation,Hole oil diameter,d=15 mmDrilled in a steel plate ha...

Q: Four wheel loads rolls as a unit across a 18-m span. The loads are 50 kN, 30 kN, 20 kN, and 10 kN se...

A:

Q: Q4. A block is connected to a spring of length s that is initially unstretched. Then the block is gi...

A:

Q: 2. If the bulk modulus for water at 70°F is 319 , determine the change in pressure required to in re...

A:

Q: 1 N 3 N 0.25 m 5 N For this example you will be 0.45 m calculating it around the COG (g on the diagr...

A:

Q: Which is true for every stress state? Choose the one correct option? A) THe plane stress states hav...

A: The correct option are:- B

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft cente...

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost othe...

Q: Calculate the specific weight, density, specific volume and relative density of oil which has weight...

A: GIVEN DATA- A OIL HAS WEIGHT 7N/litre WE HAVE TO FIND WEIGHT DENSITY , DENSITY , SPECIFIC VOLUME AND...

Q: If an aircraft has a 393 m/s velocity, determine its mach number if air is at 692K. Round your answe...

A:

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

A:

Q: 5. The wood pole is supported by two cables of 4-in. diameter. The turnbuckles in the cables are tig...

A:

Q: Three reservoirs are connected by pipes that meet at a junction. Reservoir A (EI. 140 m) is connecte...

A: CONTINUITY EQUATION A continuity condition or transport condition is a condition that portrays the v...

Q: divisions 2.1300 divisions note: the link for the calculations is provided https://www.

A:

Q: fluid is flowing in a glass pipe at a rate of 0.587 kg/s. The pipe has a diameter of 67.5 mm. If the...

A:

Q: A 150 mm diameter pipe carries 81.3 L/s of water. The pipe branches in to two pipes one is 50 mm in ...

A:

Q: Compute the head loss (in meters) in 3000 m of horizontal, cast iron pipe with nominal pipe size of ...

A: Length of pipe, L=3000 mPipe = 350 mm nominal diameter SCH 60Average velocity of water, V=2.1 m/sVis...

Q: During the General Enhanced Community Quarantine, we were mandated to stay and work from home. We do...

A: Draw a diagram showing the five displacements at home. Here, 3 displacements are between the room a...

Q: A 6.2m diameter balloon is filled with helium at 24°C and 183.18kPa. Determine the mass of the heliu...

A:

Q: Find the velocity, acceleration, and speed of a particle with the given position function. r(t) = t2...

A: Velocity is the rate of change of position. Acceleration is the rate of change of velocity.

Q: The location of the centroid of the shaded area about x-axis is

A: TO FIND Location of the centroid of the shaded area about x-axis.

Q: The rows of staples AB contained in the stapler is glued together so that the maximum shear stress t...

A:

Q: per hr at 20°. Determine the unit weight of be ufficient to give 33.5 m horizontal center-to-ce e to...

A:

Q: A water tank with a capacity of 1500 L is desired to be completely filled in about 1.5 hours. The to...

A: Answer: The power input to the pump is 0.0800 kW.  

Q: A 27 kg slab slides down a 17° inclined plane on a 2.0 mm thick film of oil with viscosity equal to ...

A: Answer: The terminal velocity of the slab is 7.648 m/s.  

Q: Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced by ...

A:

Q: 1. Loads are applied on a pipe made up of steel, bronze and aluminum. The forces and areas are shown...

A: Given:P=3000 lbA=0.5 in2

Q: A pot contains water and is heated on a cooker. The cooker adds 23.3 kJ to the pot with 0.8 kJ lost ...

A:

Q: Segment AB of the bar is a tube with an outer diameter of 1.5 in. and a wall thickness of 0.125 in. ...

A: Given:doAB=1.5 int=0.125 indBC=0.75 in 

Q: A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central ...

A:

Q: 8 KN 4 kN 15 kN m 0.5 m

A: Given

Q: two light pulleys are fastened together and form an integral unit. They are prevented from turning a...

A: To determine the magnitude R of the force supported by the bearing O for the applied 25-kN load.

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is...

A:

Q: Compute the head loss (in meters) in 3000 m of horizontal, cast iron pipe with nominal pipe size of ...

A: