Pls answer, thankyou PROBLEM 2Given is a truss structure:Where:• Working shear stress for the rivets is 70 MPa• Working bearing stress due to rivets is 140 MpaThickness of the member is 5 mmThickness of the Gusset plate is 6 mmRivet diameter is 15 mmDetermine the no. of rivets to fasten the member BD50 kN30 kNBD5m4 m4 m4 m3 m Good Luck...PROBLEM 1The bar AB is supported by a frictionless inclined surface at A and a % indiameter pin at B that is in double shear. Determine the shear stress inthe pin when the vertical 1500 Ib force is applied, Neglect the weight ofthe bar1500 Ib4 ftB4 ft8025 o

Answered: Image /qna-images/answer/94cfe375-5b70-4214-a500-244be1bb4576.jpg

The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is in double shear. Determine the shear stress in the pin when the vertical 1500 Ib force is applied, Neglect the weight of the bar 1500 lb 4 ft B 4 ft 25 e

The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is in double shear. Determine the shear stress in the pin when the vertical 1500 Ib force is applied, Neglect the weight of the bar 1500 lb 4 ft B 4 ft 25 e

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate.
A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. Determine the magnitude and location of the highest bending and torsional stresses in the 1" diameter shaft.
For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
The T-bracket is formed by welding together two cylindrical rods AB and CD. If the allowable shear stress is 80 MPa, what is the smallest allowable diameter of rod AB? Neglect the stress caused by the transverse shear force
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?
Read with understanding and solve the following problem carefullyand honestly: Write your solution on a separate sheet of paper.1. In the figure, assume that a 20-mm diameter rivet joins the plates which are100 mm wide.a. If the allowable stresses are 140 MPa for bearing in the plate material and 80MPa for shearing of the rivet, determine the minimum thickness of each plate.(Ans. t = 9 mm) b. Under the conditions specified in part (a), what is the largest average tensilestress in the plates? (Ans. δt = 34.91 MPa)
Mechanics Lesson The 6 kN force is in the vertical direction, while the P=7.5 kN force is in the z direction.Since the safe shear stress is 60 MPa, determine the smallest allowable diameter of the AD shaft.
2. A 6 mm diameter pin is used in connection C of the pedal shown. Knowing that P = 500 N. Determine: 1. The average shear stress in the pin. 2. The average crushing effort in the pedal C. 3. The crushing stress in the supports of C. The figure is in the attached image
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.67-in .-diameter pin at A, and the 0.26-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5411 lb. Round off the final answer to two decimal places.
A rectangular piece of wood, 50mm by 100mm in cross section, is used as a compression block shown. Determine the axial force P that can be safely applied to the block if the compressive stress in wood is limited to 25 MPa and the shearing stress parallel to the grain is limited to 10 MPa. The grain makes an angle of 20° with the horizontal, as shown.
A 35-mm diameter rivet joins the plates that are each 150 mm wide. The allowable stresses are 200 MPa for bearing in the plate material and 80 MPa for shearing of the rivet. Determine the minimum thickness of each plate. Answer: t = ___________________
The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.