I need the answer quickly For the following system:a. Find the total number of watts, volt-ampers reactive, and volt-ampers, and F,. (putyour answer in a table)b. Find the current Is.Q.4Load 230 W40 VAR (L)Load 1Load 3100 VAR (L)F, = 0200 WE = 220 V 20°F, = 1%3D%3D

Answered: Image /qna-images/answer/b704caa0-12aa-4e39-babf-c538955fd585.jpg

Answered: Q.4 For the following system: a. Find…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Flux Luman output per 200 W lamp Luman output per 500 W lamp Number of 500W lamps required Number of 220W lamps required Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
Electric Machine-check image, all question there. Consider the above equivalent circuit of IM. A three phase, Y connected , 215 V (line to line), 7.5Kw , 60Hz , three pole IM has the following parameter values in Ω/phase referred to the stator R1=0.294Ω , R2=0.144 Ω, X1=0.203 Ω, X2=0.409 Ω, Xm=10.25 Ω The total friction , windage and core losses may be assumed to be constant at 350W independent of load, For a slip s=0.02, compute the followings a)Stator current b)Power factor(pf) c)Rotor speed d)Power Output(shaft) e)Output(shaft) torque f)Efficiency
Use mesh or maxwell's method to solve for the unknowns. Calculate also the Power Supply and Power Received. Note: Use 10V for both voltage sources and 10 amperes for the current source.
The subject is: Smart Grid Please send the answer by typing ONLY. I don't want any handwritten. Q1- A 3 phase feeder having a resistance of 3 ohms and a reactance of 10ohms supplies a load of 2 MW at 0.85 pf lagging. The receiving end voltage is maintained at 11kV by means of a static condenser drawing 2.1 MVAr from the line. Calculate the sending end voltage and p.f. Also find the voltage regulation and efficiency of the feeder. Assume Delta connected.
A 30 x 30 x 30 m room is installed with a fan designed to supplyair every second. If the losses due to ducting is measured at0.15 m, determine the required power of the fan in Watts.
A 3-phase transmission line is being supported by three-disc insulators. The potentials across top unit (i.e. near to the tower) and middle unit are 8 KV and 11 KV respectively. Calculate: 1) The ratio of capacitance between pin and earth to the self-capacitance of each unit 2) The line voltage 3) String efficiency Subject Power Transmission And Distribution
Airframe Electrical system Question: State the four common aircraft system voltages. (Source: FAA AC 43.13-1B/2B)
From Figure 5, Maxwell Mesh method, Calculate ( C ) Current 3
A power transmission line conducts current from a 6000V generator to three loads A,B,C, the loads are located 4.7 and 10Km from the generator and absorb 60,20,100A, respectively. The resistance of the line is 0 .1ohm/Km see figure 3.21a) Calculate the tension in the loads A,B,Cb) Calculate the percentage of voltage drop between generator and load C
The data for a wind turbine is given below: Wind speed = 14 meters/sec, Length of blade = 10 meter Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 40square meters. b. The wind rotor swept area is 314 square meters. c. The wind rotor swept area is 31.4 square meters. d. The wind rotor swept area is 62.4 square meters.
One 33kV, 50Hz, 3-phase underground cable, 3 single-core cables of 4km length are used. The diameter of the conductor is 2.5cm and the circular thickness of the insulator is 0.5cm. (Insulation dielectric constant is 3) A) cable / phase capacitance? B) charging current / phase? C) Determine the total charge KVAR. ?
A high voltage transmission line conducts 1000 A starting at 700 kV for a distance of 160 km meters. If the resistance in the wire is 0.3 ohms/km, what is the power loss due to resistive losses? (M=10^(6))

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Q.4 For the following system: a. Find the total number of watts, volt-ampers reactive, and volt-ampers, and Fp. (put your answer in a table) b. Find the current Is. Load 2 30 W 40 VAR (L) Load 1 Load 3 100 VAR (L) F, - 0 200 W E - 220 V 20° F, = 1 %3! %3D