Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m/sec. 3. Specific speed.

Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m/sec. 3. Specific speed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
A pump, geometrically similar to the 12.95-in model inFig. , has a diameter of 24 in and is to develop 30 hpat BEP when pumping gasoline (not water). Determine(a) the appropriate speed, in r/min; (b) the BEP head, in ft;and (c) the BEP flow rate, in gal/min.
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
A single-acting reciprocating pump, with a diameter of 18 cm and a stroke of 30 cm, delivers water at a rate of 0.18 m3/s. What is the percentage slip it delivers at 1,500 rpm?
A turbine develops 10 MW under a head of 25 m at 135 rpm. a) What is the specific speed? b) What would be its normal speed for a head of 20 m c ) it's output under a head of 20 m?
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor?
1) A single-stage centrifugal pump operating at 650 rpm and delivering 250 gallons per second has a specific speed of 4750 rpm. The suction flange is 609.6 mm in diameter and has a vacuum pressure of 70 kPa. The discharge flange is 22 inches in diameter and its centerline is 30.5 cm above the suction centerline. What discharge pressure in kPaa would you expect to find?
A pump delivers 20 cfm of water having a density of 62 lbs. per cubic foot. The suction anddischarge gage reads 5 inches Hg vacuum and 30 psi respectively. The discharge gage is 5 ft abovethe suction gage. If pump efficiency is 70%, what is the motor power?
The diameter of a large offshore wind turbine is 120 m, assuming air density, 1.2 kg/m3, compute the available wind power 5, 10, 15 m/s . What is the available wind power density for wind speed of 7.5 m/s?
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid against a head of 25 m. The diameter of the impellers being 24 cm and the speed of 1800 rpm. A pump is to be made up with a number of stages in series of similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a totalhead of 250 m. Find the diameter of the impellers and the number of stages required in this case. Answer: D = 46.63 cm, n = 6 stages
The water turbine of a 5-MW hydro-power plant has specific speed of 40 rpm and discharge of 2020 lps. What is the approximate diameter of the jet in mm?