[Q1] A carrier signal (peak amplitude = 39V, frequency = 100MHZ) is frequency modulated by the baseband signal (peak amplitude = 5V, bandwidth = 12.02kHz). The frequency deviation is 77.53kHz, and the load is 51N. Determine (a) the load power, (b) the bandwidth of the transmitted signal. (consider only |Jn(B)| > 0.1). %3D %3D %3D

[Q1] A carrier signal (peak amplitude = 39V, frequency = 100MHZ) is frequency modulated by the baseband signal (peak amplitude = 5V, bandwidth = 12.02kHz). The frequency deviation is 77.53kHz, and the load is 51N. Determine (a) the load power, (b) the bandwidth of the transmitted signal. (consider only |Jn(B)| > 0.1). %3D %3D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For an Armstrong indirect FM transmitter with the crystal carrier oscillating at 210 kHz, the crystal reference oscillating at 10.2 MHz, the sideband voltage is 0.018 V, the carrier input voltage to the combiner is 5V, the first and second multipliers are both 40, and the modulating signal frequency is 2 kHz, determine: a.) modulation index at the output of the combining network and the power amplifier; b.) frequency deviation at the same two points; and c.) the transmit carrier frequency.
1. Select the correct statement(s) regarding amplitude modulation (AM). a. If the AM Index is greater than 1 (i.e., µAM>1), then over modulation occurs leading to signal distortion b. With AM, the message is captured as amplitude changes to the carrier’s amplitude. c. The AM modulated carrier bandwidth is dependent upon the baseband signal’s frequency bandwidth d. All of the above are correct 2. What is true about the frequency bandwidth of a modulated electrical or electromagnetic (EM) signal? a. signal bandwidth is only determined by the frequency of the unmodulated carrier wave b. modulation technique and the amount of information transmitted determines the signal’s bandwidth c. only the baseband signal determines frequency bandwidth; i.e., modulation technique has no impact on bandwidth d. a and c are true 3.Regarding carrier modulation, identify the carrier signal variable(s)…
amplitude value of output voltage (Vout) = ?? Note1 : E-MOSFET output empedance rd= 70kΩ Note2: capacitors are of negligible size at midband frequency Note3 : 5kHz in midband frequency
5. The following data is available: fc= carrier frequency = 750kHz, Ac= maximum amplitude of the unmodulated carrier = 10V fm= modulator frequency = 300Hz-8kHz modulation index m=0.5 a) What is the frequency of the upper sideband? b) What is the frequency of the lower sideband? c) What is the amplitude of the modulating signal? d) What is the maximum amplitude of the envelope of the modulated signal? e) What is the minimum amplitude of the envelope of the modulated signal? f) What is the bandwidth of the modulated wave? g) Write an expression for the modulated wave
1. For a system with FM modulation, the amplitude of the unmodulated carrier is 12Vp, if the modulation index is 1.5 and the load resistance RL is 10 ohms,a) determine the power in the unmodulated carrier; b) Determine the power at the carrier frequency and at each significant side frequency for the modulated wave. What value of power do you obtain when adding the values obtained in question (b)?
q/A given AM (DSB – LC) transmitter develops an unmodulated power outputof 1 kW. Across 50Ω resistive load. When a sinusoidal test tone with a peakamplitude of 5? is applied to the input of the modulator, it is found that thespectral line for each sideband in the magnitude spectrum for the output is 40%of the carrier line. Determine the following quantities in the output signal:a-The modulation index.b-The peak amplitude of the lower sideband.c-The ratio of total sideband power to carrier power.d-The total output power.e-The total average power in thr output if the peak amplitude of the modulationsinusoid is reduced to 4 volt.
An FM modulator has kf=30kHz/V and operates at a carrier frequency of 180 MHza. Find the output frequency for an instantaneous value of the modulating signal equal to150mV. b. If the carrier signal is modulated by a 2Vrms sine wave. Calculate the peak frequencydeviation. c. Using the given in the previous number, also find the bandwidth using the Bessel table below for thePM signal when the message frequency is (a) doubled, (b) halved, but all else remains constant.
Bandwidth requirements:a. Find the minimum required bandwidth for the baseband transmission of a 32-level PAM pulse sequence with a data rate, R of 10000 bps if the system transfer characteristic consists of a raised-cosine spectrum with 100% excess bandwidth (roll-off, r = 1.0).b. Find the minimum required double-sideband (DSB) bandwidth for transmitting the modulated PAM sequence where the system transfer characteristic is the same as in part (a).c. Repeat part (a) with roll-off, r = 0.5.d. Repeat part (b) with roll-off, r = 0.5.e. Repeat part (a) with roll-off, r = 0.f. Repeat part (b) with roll-off, r = 0.
1.) Answer the following: a. At 50% modulation DSBSC, what is the percentage power saving?b. At 75% modulation, what percentage of the total transmitted power is in the sideband?c. For conventional AM, the useful power, that is, the power that carries the information is rather small reaching a maximum of ______.Select the correct response:-One-fifth of the total signal power at 100% modulation-One-third of the total signal power at 100% modulation-One-fourth of the total signal power at 100% modulation-One-tenth of the total signal power at 100% modulation
1.Select the correct statement(s) regarding frequency modulation (FM) bandwidth. a. the more the carrier frequency is allowed to change frequencies (Δf), the smaller the modulated signal bandwidth b. the larger the FM index, β, the larger the modulated signal bandwidth c. as you increase kvco, you decrease modulated signal bandwidth d. all statements are correct 2. Select the correct statement(s) regarding baseband signal modulation. a. with modulation, a baseband signal can be moved to a higher frequency thus preventing baseband signal interference b. modulation techniques are only required for analog information signals, since digital signals are represented by discrete logical values of “1” and “0” c. modulation eliminates the baseband signal’s frequency bandwidth, thus enabling greater efficiencies when transmitting a modulated carrier signal d. all statements are correct 3. A…
Question 1. Select the correct statement(s) regarding amplitude modulation (AM). a. If the AM Index is greater than 1 (i.e., µAM>1), then over modulation occurs leading to signal distortion b. With AM, the message is captured as amplitude changes to the carrier’s amplitude. c. The AM modulated carrier bandwidth is dependent upon the baseband signal’s frequency bandwidth d. All of the above are correc
The SNRi of an FM transmitter is determined to be 24.093dBV. Solve for the peak frequency deviation caused by the noise if the transmitter sensitivity is determined to be 368.903Hz/V, and a modulating signal of 13.926V and the modulating index is kept at 4