Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m? on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m?.

Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m? on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m?.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.
the solid circular shaft rod has an original diameter of 20mm. when the load of 50kN is applied the shaft stretches 1.4mm and it has a Poisson's ratio of 0.25. Calculate the change in diameter of the shaft?Assume shaft is in the elastic region.
A solid 1.40-in.-diameter steel [G = 12,000 ksi] shaft is subjected to the torques shown. Determine the magnitude of the maximum shear stress in shaft segment (1). a 1.82 ksi b 2.45 ksi c 3.86 ksi d 3.01 ksi e 2.85 ksi
A steel flat 10 cm wide and 2 cm thick is bent into a circular arc of 50m radius.Find the maximum intensity of stress induced. Take E = 2.05 * 10 ^ 5 N/mm².
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
A solid aluminum shaft 2 inches in diameter is subjected to two torques. Determine the maximum shearing stress in each segment and the angle of rotation of the free end. Use G = 4 × 106 psi.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)