Q1: A hexagonal cross section bar as shown in figure (1) below, is used as a simply supported beam at its ends with length of 4 m. The beam carries a uniformly distributed load (w) of 75 kN/m. For a section at 2 m from the left- hand support, determine the shear stress at (a) the neutral axis and (b) x.

Q1: A hexagonal cross section bar as shown in figure (1) below, is used as a simply supported beam at its ends with length of 4 m. The beam carries a uniformly distributed load (w) of 75 kN/m. For a section at 2 m from the left- hand support, determine the shear stress at (a) the neutral axis and (b) x.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Consider a 180-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 60 kN-m and 68 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 120 mm, b2 = 30 mm, b3 = 200 mm, d1 = 65 mm, d2 = 175 mm, d3 = 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Exercise caution in choosing the value of "c". (Be it known obviously that for beams with irregular cross-sections, Ctop ≠ Cbottom) Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.
Consider a 155-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 75 kN-m and 79 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 135 mm, b2= 50 mm, b3= 205 mm, d1= 65 mm, d2= 180 mm, dz= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Shear force acting on section H in the figure Shear stress y when T = 50 kN acts Draw the distribution of zy.
a. Calculate the moment of inertia (I) of the given cross–section b. Calculate the first moment of area (Q) at certain depth by using 25 mm increments. c. Calculate and draw the horizontal shear stress distribution of the beam at 0.2 m from the left support
Two uniform loads of 112 kN/m acting downward are supported by a uniform upward pressure of q as shown in the figure.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive moment = 1970.65 kN-m Maximum negative moment = 1480 kN-m Location of maximum shear from the left end of beam = 22 m Location of maximum moment from the left end of beam = 15.23 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.