Q1: A Power station of 10 MW is to supply two regions A and B, The daily of loads are given below. Time in hours Midnight -9 Region A in kW 19-midnight 9-12 12-17 17-18 18-19 600 2500 800 5000 4000 Time in hours midnight -8 8-13 13-14 14-17 17- midnight Region B in kW 800 5000 800 5000 Find the power consumed in period 17- midnight on region B, and draw the load curve of total power station, if the maximum load 7500 kW and load factor 0.5261 on the total power station.

Q1: A Power station of 10 MW is to supply two regions A and B, The daily of loads are given below. Time in hours Midnight -9 Region A in kW 19-midnight 9-12 12-17 17-18 18-19 600 2500 800 5000 4000 Time in hours midnight -8 8-13 13-14 14-17 17- midnight Region B in kW 800 5000 800 5000 Find the power consumed in period 17- midnight on region B, and draw the load curve of total power station, if the maximum load 7500 kW and load factor 0.5261 on the total power station.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28P: For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be...

See similar textbooks

Similar questions

for the circuit shown, find the maximum power delivered to this load resistor? Please answer in typing format solution please only typing
Transmission and distribution lines are important components of any power system study. Aluminium cable steel reinforced (ACSR) (with steel in the centre – as shown in Figure Q1 is normally chosen instead of copper for transmission Explain: (a)The choice of aluminium instead of copper (b)The need to use and place steel at the core
Determine the symmetrical components of the three currents ?? = 10 ∠ 0A; ?? =100 ∠ 2500 A; and ?? = 10 ∠ 1100 A.
50. It is the resistance of a material when there is no supply. Hot Resistance Infinite Resistance Cold Resistance Irresistible 49. What is the phase sequence of a three-phase motor for which Van = 220∟-100, Vbn=220∟140 abc acb aab bba 48. The prefix pico stands for: 10^-9 10^9 10^12 10^-12 47. A source is connected to three loads Z1, Z2 and Z3 in parallel. Which of these is not true? P = P1+P2+P3 S = S1+S2+S3 Q = Q1+Q2+Q3 all are true 46. The Thevenin impedance of a network seen from the load terminals is 80+j55 ohm. For maximum power transfer, the load impedance must be: 80+j55 -80+j55 -80-j55 80-j55
Question No.14: A peak load on the thermal power plant is 75 MW. The loads having maximum demands of 35 MW, 20MW, 15 MW and 18MW are connected to the power plant. The capacity of the plant is 90 MW and annual load factor is 0.53. Calculate the average load on power plant, energy supplied per year, demand factor and diversity factor.
Calculate ( C ) Load current, Calculate ( D ) Power in the load resistor or Power in the 50 ohms resistor, Calculate ( B ) Rth, Calculate ( A) Vth
three transformers connected as indicated below to step the voltage down from 13,200V to 460V. a) determine the ratio of the transformer if the transformers are connected wye-delta. b) determine the ratio transformation if the transformers are connected wye-delta. c) determine the ratio of transformation if the transformers are connected delta-wye. d) determine the ratio of the transformation if the transformers are connected delta-delta. BOX THE FINAL ANSWER AND USE 4-5 DECIMAL PLACES FOR THE ANSWER subject: ELECTRICAL APPARATUS AND DEVICES
Arrange a simple three-phase system and measure the power consumed by the load. You may use wattmeter or any other digital meter, while measuring three-phase power. The connection diagram is shown in Figure 3. Your report should show details of the three-phase load and connection diagram relating to the power you have measured. This work should be evidenced by photograph in the report.
A computer's power supply converts mains AC to low-voltage regulated DC power for the internal components of a computer. You are building a new computer. You are deciding which type of power supply to install. Which of the following definitions BEST describes a valid type of power supply? Correct Answer: A single-rail power supply provides one rail (PCB trace). This provides the best safety for the computer by providing a single point of shutdown in the event of a short circuit. Correct Answer: A single-rail power supply provides one rail (PCB trace) used to always provide equal wattage to all devices attached to the power supply. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to provide equal wattage to the devices attached to each rail. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to balance the power load between multiple circuits, which prevents any one circuit from becoming overloaded.
Discuss the concept of load shedding and its purpose in a power system.
Is it right P that given is it input or output power, more over delta/Y 377V/281V ,2.99A/3.15A what does it mean for these . Also free shaft conditions mean?
62. A power plant costumer draws power at 220 volts from transformers on a pole. Current transformers with ratio of 200/5 are used to meter the electrical usage. What is the multiplier of the kW-hr and demand meters? a. 50 b. 45 c. 40 d. 55