A hydro-plant and a steam plant are to supply a constant load of 95 MW for 1 week (168 h). The unit characteristics are: Hydro-plant: q = 300 + 15 Pµ acre – ft/h Steam plant: Hs = 53.25 + 11.27 Pg + 0.0213 P? Let the hydro-plant be limited to 9,000 MWh of energy. Solve for Ts, the run time of the steam unit. Os PH S 100 MW 12.5 < Ps < 50 MW

A hydro-plant and a steam plant are to supply a constant load of 95 MW for 1 week (168 h). The unit characteristics are: Hydro-plant: q = 300 + 15 Pµ acre – ft/h Steam plant: Hs = 53.25 + 11.27 Pg + 0.0213 P? Let the hydro-plant be limited to 9,000 MWh of energy. Solve for Ts, the run time of the steam unit. Os PH S 100 MW 12.5 < Ps < 50 MW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=200 Volts, Time period is 10 milli seconds and P =30 degrees. Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.8 ms = b) Angular frequency D
Question 13 of 15 Determine: The figure below shows a vapor power cycle that provides process heat and produces power. The steam generator produces vapor at 500 lbf/in.², 800°F, at a rate of 8 x 104 lb/h. Seventy percent of the steam expands through the turbine to 10 lbf/in.² and the remainder is directed to the heat exchanger. Saturated liquid exits the heat exchanger at 500 lbf/in.² and passes through a trap before entering the condenser at 10 lbf/in.² Saturated liquid exits the condenser at 10 lbf/in.² and is pumped to 500 lbf/in.² before entering the steam generator. The turbine and pump have isentropic efficiencies of 85% and 89%, respectively. For the process heat exchanger, assume the temperature at which heat transfer occurs is 465°F. Let To -60°F, po - 14.7 lbf/in.² Steam generator 6 7p=89% P₁ = 500 lbffin,² T₁ = 800°F Heat exchanger Pump m₂ ND 1 (y) (1-y) √n process 7=85% P4=500 lbf/in.2 saturated liquid (a) the magnitude of the process heat production rate, in Btu/h. P3=10…
The voltage a cross the terminals of a certain 3-phase machine is 400 <40 ͦ V whereas the current which is assumed to be into this machine is 55<-60 ͦ Find the real and reactive powers consumed or delivered by this machine. What is the type of this machine?
a steam 1. A constant load (= 150 MW) supplied by a hydro and unit. Find the generation schedule for 5 days (120 hours). Assume that generation of hydro unit limited to 12000 MWh. MW Hydro unit: 2 Steam unit: F(P₂) = 160+4Ps +0.025 P² 20
1/ Suppose that there are two types of H.V.T.Ls operating at the same voltage and carrying the same current, but one of them with smooth shapewhile the other with standard shape. Which of them, you will choose? a. choosing the smooth one. b. choosing the standard one. c. choosing the one with hollow construction shape. d. all these answers are wrong. 2/ As the ambient temperature in crease the disruptive critical voltage of coron a is: a. Decreased b. Increased c. No effect d. All these answers are wrong. 3/ Using HV underground cable improvevoltageprofile and power factor in any loaded inductive electrical grid because. a. Due to its inductive power effect. b. Due to resistive Effect. c. Due to its capacitive power effect. d. All of the above answers are wrong.
List 3 different concepts of Electricity(gravity) not hydro generation using weights design. Each concept must have an introduction and design description. Include a photo of each trenching machine design and modeling concept. For Example : Mass electricity generation
Suppose there is a load that needs 120W of power and is located 50ft from a generator with a total resistance of 0.2525 Ohms. The load can be designed to operate at 12V or 120V. Find the voltage drop and power losses in the connecting wire for each voltage and comment on the results.
What is a "Peclet number?" Give its significance. Additionally, calculate the overall flux using the Peclet number.
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
Create a short essay based on your own understanding and opinion about the question, “How does a dc generator work?”. Minimum of 150 words.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
3) Resistor is used as load in the circuit below. T1 and T4 thyristor is triggered at 30 degrees, T2 and T3 thyristor is triggered at 210 degrees. The effective voltage of the AC voltage applied to the circuit is 120 V. a) Draw the graph of the voltage on the load resistor.b) Neglect the voltage drop across the thyristors and find the average value of the load voltage.