Q1/ An aluminum rod 4.0 cm in diameter and 10 cm long protrudes from a wall that is maintained at 250°C, and air at 40°C is forced it at a velocity of 50 m/s. If the surface emissivity is 0.7, Calculate the total heat loss per unit length if the walls of the enclosing room at 15 °C ?. T h, T A, = A

Q1/ An aluminum rod 4.0 cm in diameter and 10 cm long protrudes from a wall that is maintained at 250°C, and air at 40°C is forced it at a velocity of 50 m/s. If the surface emissivity is 0.7, Calculate the total heat loss per unit length if the walls of the enclosing room at 15 °C ?. T h, T A, = A

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.38P

See similar textbooks

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
A 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your calculation.
Q2: Air at standard conditions of I atm and 27°C flows over a flat plate at 20 m/s. The plate is 60 cm square and is maintained at 97°C. Calculate the heat transfer from the plate. Answers: Q= 681 W,
Flue gases from an incinerator are released to atmosphere using a stack that is 0.6 m in diameter and 10.0 m high. The outer surface of the stack is at 40°C and the surrounding air is at 10°C. Determine the rate of heat transfer from the stack assuming (a) there is no wind and (b) the stack is exposed to 20 km/h winds.
Q6: A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constant temperature of 57+C and exposed to atmospheric air at 4°C. Calculate the heat lost by the plate. Answers: Q=1907 W
A straight cylindrical fin 0.6 cm in diameter and 6 cm long protrudes from a magnesium block heldat 300°C. Air at 35°C is forced past the fin so ℎ̅ is 130 W/m2K. Calculate the heat removed by the fin, the finefficiency, and the fin effectiveness.
A 5.0-cm-diameter cylinder is heated to a temperature of 200 oC, and air at 30 oC forced across it at a velocity of 50 m/s (h = 180 W/m2K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 oC. Comment on your calculation. COMPLETE SOLUTION
Consider two cases involving parallel flow of dry air at V=V= 2.5 m/s, T∞=45°C, and atmospheric pressure over an isothermal plate at Ts=20°C. In the first case, Rex,c=R⁢ex,c=5 × 105, while in the second case the flow is tripped to a turbulent state at x=0 m. a. At what x‐location, in m, are the thermal boundary layer thicknesses of the two cases equal? in m b. what is the q'' lam at W / m^2 c. what is the q'' turb at W / m^2
Q3: Air flows across a 20-cm-square plate with a velocity of $ m/s. Free-stream conditions are 10-C and 0.2 atm. A heater in the plate surface furnishes a constant heat-flux condition at the wall so that the average wall temperature is 100-C. Calculate the surface heat flux and the value of h at an x position of 10 cm. Answers: Q= 1414 W, b= 13.3 Wm?.C
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
Imagine a plate 0.1 m long by 0.1 m wide at a temperature of 80 °C. Water is passed over its surface at a speed of 0.1 m/s and 40°C. Calculate the heat dissipated by the plate. Assume the following properties of water at 60 °C: k= 0.651 W/mK, Pr=3.02 y v = 0.478 x 10-6 m²/s.
Air at 20oC and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and 100 cm depth and is maintained at 60oC. Calculate (a) velocity boundary layer thickness at the leading edge, (b) thermal boundary layer thickness at the distance of 10 cm from the leading edge, and (c) thermal boundary layer thickness at the trailing edge.