Q1: Complete the field notes shown in table by computing and recording the elevation for each point. (Use any method you find suitable) Point BS IS FS Rise/Fall HI Elevation (m) 1 1.55 233 2.75 0.58 3 0.82 4 1.83 1.10 2.58 6. 0.42 7 3.25 0.57 8. 1.86 9. 1.74 10 2.35 0.78 11 2.65 1.56 12 0.89 1.89 13 1.25 14 2.56 1.13 15 0.89 1.75 16 0.53 17 0.43 18 0.68 19 0.87 20 0.79

Q1: Complete the field notes shown in table by computing and recording the elevation for each point. (Use any method you find suitable) Point BS IS FS Rise/Fall HI Elevation (m) 1 1.55 233 2.75 0.58 3 0.82 4 1.83 1.10 2.58 6. 0.42 7 3.25 0.57 8. 1.86 9. 1.74 10 2.35 0.78 11 2.65 1.56 12 0.89 1.89 13 1.25 14 2.56 1.13 15 0.89 1.75 16 0.53 17 0.43 18 0.68 19 0.87 20 0.79

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STA BS FS 1 5.87 2 7.03 6.29 3 3.48 6.25 4 7.25 7.08 5 10.19 5.57 6 9.29 4.45 7 4.94 a. Determine the elevation at Sta. 7, in meters if the elevation at station 1 is 392.25m. b. Determine the elevation of the instrument where the surveyor can get readings from stations 3 and 4.
The distance between points A and B was determined by stadia survey using a leveling The stadia readings were recorded as follows: upper reading = 2.45m middle reading = 1.80m lower reading = 1.15m Stadia interval factor = 100 stadia constant = 0. What is the distance between A and B?
: Determine the graph and conversion of the following angles.1. Convert the following azimuth 190º15.40'45” to heading.2. Graphic 66º7´9”3. Convert the following heading S 74º9'30” W to azimuth.4. Convert the following azimuth 200º46´7.12” to heading.5. Graph 245º52´14”
Measurement of three horizontal angles about point P: are APB= 12°31'50'' BPC= 37°29'20'', and CPD= 47°36'30''. If the measurement of the single angle APD is 97°37'00'', determine the most probable values of the angles.
A dumpy level is set up at one end of a line 120 m long for the purpose of determining the instrument’s stadia interval factor. The line is marked by hubs at every 30 m and a stadia rod is held at each hub. The stadia intercepts at each location of the rod were observed as follows: 0.308, 0.613, 0.918 and 1.222 meters, respectively. The average value of the instrument’s stadia interval factor is:
FUNDAMENTALS OF SURVEYING 1, FIELD 1.) A backsight reading of 2.73m is taken to a point A and subsequently a foresight reading of 1.35m is taken on point B from a level station established midway between the two points. a)What is the difference in elevation between points A and B? b) If the elevation of A is 386.70m above sea level, what is the elevation of B?
Surveying In order to locate the position (P) of a sounding boat, the angles APB & BPC subtended at P by three points A, B and C on the shore were measured with a sextant and found to be 28º 42’ 40” and 30º 28’ 20” respectively, the point B & P being on opposite of AC. The length of AB & BC scaled from a map were 662 m and 4662 m respectively, and the angle ABC was 60º 50’ 40”. Carry out all the necessary calculations to compute the distances PA, PB and PC.
Reciprocal leveling between points A and B, located on opposite banks of a wide river gives the following readings in meters. From the first setup near A: on A, 0.993; on B, 2.076, 2.077, and 2.078. For the set-up near B the readings are: on B, 2.549; on A. 1.463, 1.462, and 1.463. If the elevation of A is 925.28 meters determine the true difference in elevation between the two points and the elevation of B
n Rising and Dipping distance which equation is correct? a. 2.20 X √ Elevation b. 4.10 X √ Elevation c. 3.08 X √ Elevation d. 2.08 X √ Elevation
Observations from unknown pointFlagpole: 18°05'37''King's Battery: 38°03'36''Plumpud: 52°55'01'' Y XFlagpole +49835.50 +59098.10King’s Battery +50750.11 +58299.80Plumpud +50345.40 +58164.13 1. Calculate the coordinates of your unknown point using Q-point method for resection.
A line XYZ is measured on the slope in two segments. The first segments XYmeasures 824.45m and the second segment YZ measures 1244.38m.If thedifference in elevation between points X and Y is 4.25m and that between Y andZ is 6.47m,determine the horizontal length of the measured line.
A line of levels was run from benchmarks A to B, B to C, and C to D. The elevation differences obtained between benchmarks, with their standard deviations, are listed below. What is the difference in elevation from benchmark A to D and the standard deviation of that elevation difference? (a) BM A to BM B = +12.68 ±0.10 ft; BM B to BM C = -8.23 ± 0.18 ft; and BM C to BM D = -14.66 ± 0.06 ft(b) BM A to BM B = -15.324 ± 0.022 m; BM B to BM C = -10.250 ± 0.015 m; and BM C to BM D = -16.892 ± 0.008 m