Q1/ Explain the pressure loss in the four- section petroleum well drilling system 1. Surface connections. 2. Pipes including drillpipe, heavy walled drillpipe and drill collars. 3. Annular areas around drillpipes, drillcollars, etc. 4. Drillbit. Note: The explanation is in text format, with the equations and drawings, if any, mentioned

Q1/ Explain the pressure loss in the four- section petroleum well drilling system 1. Surface connections. 2. Pipes including drillpipe, heavy walled drillpipe and drill collars. 3. Annular areas around drillpipes, drillcollars, etc. 4. Drillbit. Note: The explanation is in text format, with the equations and drawings, if any, mentioned

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The ratio of entry diameter with exit diameter is 0.4 in a control volume of pipe segment. What is the corresponding ratio of entry to exit velocity? Recall Q1=Q2 and v1A1=v2A2 Correct answer has a margin of 0.1 from exact answer.
Q1.In a duct enlargement , the velocity reduces from 20 m/s to 5 m/s . If it is a 20 ° angle gradual enlargement, the pressure loss is given byCalculate the value if static regain.How will the value of static regain change if is a case of abrupt enlargement. Calculate the amount and compare
A2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:6. At sea level, atmospheric pressure is 14.7 psia (101 325 Pa). A bicycle tire (at sea level) is inflated to 50 psi (344 737 Pa). Determine the gauge and absolute pressures in the inflated tire.
Answer this as fast as you can but answer should be correct (correct answer is priority) Air leaks slowly to atmosphere from a pressurized tank at 19 bar (gage) and 27°C through a hole of diameter 2 mm. The tank volume is 1 m3. Atmospheric conditions are 100 kPa and 27°C. Determine the time for the tank pressure to decrease to 100 kPa (gauge).
The gauge pressure in a liquid at a depth of 2.7m is 55.8 kPa. What is the gauage pressure kPa in the same liquid at a depth of 6.4m. I need right solution with clear calculations.
A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two pressure lines from the probe were connected to a U-tube manometer which uses a liquid of specific gravity 1.7. The maximum velocity expected in the water tunnel was 2.3 m/s. Your job was to select an appropriate U-tube from a manufacturer which supplies manometers of different heights. The cost increases significantly with manometer height. Which of these should you purchase?
A 400 gpm piping system is composed of the following pipes and fittings. Using the chart; Determine the Following: a. Equivalent length at suction in ft b. Equivalent length at discharge in ft c. Total friction loss in the installation, in ft. Suction side (4.5” Փ) Length of straight pipe 210 ft Long sweep elbow 5 pcs Standard Tee 2 pcs Globe valve 1 pc Checked valve 1 pc Gate valve (fully open) 1 pc Discharge side (4.0” Փ) Straight pipe 200 ft Standard elbow 4 pcs Standard Tee 3 pcs Gate valve (fully open) 1 pc
Describe the concepts of independent, dependent, and extraneous variables using the illustration of a pressure measurement system.
A Prandtl tube (Pitot-static tube with C = 1) is used to measure the velocity of water. The differential manometer reading is 10 mm of liquid column with a relative density of 10. Assuming g = 9 8. m/s2 , the velocity of water (in m/s) is______
The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity of air flowing if density is 1.16kg/m3. ANSWER: 22.9
Given, Point A - Inlet of a water pipe Pressure at the inlet of a water tap = 300kPa Water Pipe internal dimension is = 30mm Water Temp = 20 degrees Point B - section of pipe Pressure = unknown Open to atmosphere. elevation drop of 20m from point A to Point B Assume frictionless piping system. Assume turbulent flow. What is the pressure and flow rate at point B?
Choose the wrong statement a)Newton's law of viscosity relates between shear stress and angular deformation b)Water hammer is caused by sudden closure of valves and creates a pressure fluctuation in the system c)Cavitation of the pump can be avoided by increasing its suction pressure d)Heat, handheld pumps, artesian well pumps may be example for positive displacement pumps e)None