Q1): Impulse turbine diameter = 3.2m O1 = O2 Angular velocity = 25 rad/s Absolute velocities V1 = 140m/s and V2 = 110m/s Power developed by the wheel = 300kw Calculate: 1. the blade velocity. Jet 25mmd V: 2. the force exerted and 3. the angle O.

Q1): Impulse turbine diameter = 3.2m O1 = O2 Angular velocity = 25 rad/s Absolute velocities V1 = 140m/s and V2 = 110m/s Power developed by the wheel = 300kw Calculate: 1. the blade velocity. Jet 25mmd V: 2. the force exerted and 3. the angle O.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: QUESTION 4 Water is discharged from the impeller of a centrifugal pump against a pressure of 10.5 m…

Q: 33. An inward flow reaction turbine running at 450 rpm has an external diameter.of 50 cms and a…

Q: It is desired to develop a 5 MW turbine under an effective head of 320 m. The turbine efficiency is…

Q: The peripheral speed of the rotor of impulse turbine is (300m/S) and the absolute velocity of air at…

A: For solution refer below images.

Q: Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the…

Q: A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400…

A: The volume flowrate of fluid passing through a cross section can be determined as the product of…

Q: ine of 2 litre capacity is to develop inax. power at 4000 rpm Volumetric efficiency at this speed is…

Q: 20. A centrifugal pump has an impeller 45 cms in diameter running at 450 rpm. The dischargė at inlet…

A: Given: Impeller diameter D2=45cm or 0.45m (Impeller diameter means diameter of the impeller at the…

Q: Water is discharged from the impeller of a centrifugal pump against a pressure of 10.5 m and a…

Q: For a single stage impulse turbine : Rotor diameter3 6 m Speed%3 2700 rpm Nozzle angle= 20°…

Q: A Pelton wheel is supplied with water under a head of 35 m at the rate of 40.5 klo litre/min. The…

A: We know of a pelton wheel that receives water at a rate of 40.5 kilo litres per minute from a head…

Q: An inward flow reaction turbine has external and internal diameters as 1.095 m and 0.553 m…

Q: A centrifugal pump impeller has a diameter of 1 m and speed of 10 m/s. Water enters radially and…

Q: Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the…

Q: A čentrilugal pump has an impeller 45 cms in diameter 20. running at 450 rpm. The discharge at inlet…

A: Solution Impeller diameter D2=45cm or 0.45m (Impeller diameter means diameter of the impeller at the…

Q: A Pelton turbine having 1.6 m bucket diameter develops a power of 3600 kW at 400 rpm under a net…

Q: At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters…

Q: Q-A Francis turbine is running at 500 rpm under a head of 190 nm. The blade angle at inlet is 50°…

A: Given: Speed of the turbine→N=500 rpm Head of the turbine→H=190 m Blade angle at inlet→θ=50° Guide…

Q: A Pelton wheel of power station develops 30,500 hP under a head of 1750 m while running at 760 rpm.…

Q: An axial-fl ow blower delivers 40 ft3/s of air that enters at20°C and 1 atm. The flow passage has a…

Q: A centrifugal pump has vanes which are radial at the outer periphery. The impeller has an outer…

Q: The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m.; blades are…

Q: 31. The absolute velocity of water at inlet to a turbine is 12 metre/sec, the guide blade angle…

A: Given:-Absolute velocity of inlet of turbine=12m/sGuide blade angle=20°d=40cm=0.4mb=10cm=0.1mTo…

Q: PROBLEM 4 A centrifugal pump delivers 26 Vs against a total head of 16m at1450 rpm. The impeller…

A: Given data: Q1=26 L/sN1=1450 rpmD1=0.5 mN2=2900 rpmH1=16 mD2=30 cm=0.3 m Need to determine the head…

Q: SThe three jet Pelton wheel is required to generate 10,000 kW under a net head of 400 m. The blade…

Q: 3.7 A reaction turbine runner diameter is 3.5 m at inlet and 2.5 m at outlet. The turbine discharge…

A: Given data: Q=102 m3/secH=145 mη=88%θ=120° Need to determine the power developed and speed of…

Q: Do the ODE of it

A: Given: Radical flow turbine Absolute velocity at inlet = V1 Outer radius at inlet = l1 inner radius…

Q: 17. A centrifugal pump has a 25 cms diameter impeller and an outlet width of 5 cms and runs at 1100…

Q: A Francis turbine has the dimensions of ri=1.42 m, r2=2.00 m.bi=2.20 m and b2=0.731m. Rotation speed…

Q: At mid-radius an axial turbine stage is designed for 50% reaction, zero outlet swirl, and an axial…

A: (a) There is no swirl in the absolute velocity leaving the rotor, . Therefore the following relation…

Q: The impeller of a centrifugal pump is of 25 cm diameter and 5 cm width at the periphery. It has…

A: In this question only one part is given so I am going to solve part one of the given question. By…

Q: The impeller of a centrifugal pump is of 25 cm diameter and 5 cm width at the periphery. It has…

Q: Q3. A centrifugal pump impller runs at 1400 rpm, and vanes angle at exit is 25°. The impller has an…

Q: Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the…

Q: A centrifugal pump impeller has an external diameter of 1.2 m and internal diameter of 0.8 m. The…

A: As per honor code and answering guidelines I can answer 1st three subparts at a time.If you want…

Q: The impeller of a centrifugal pump has a diameter of 115 mm and axial width of 21 mm at the outlet.…

A: A centrifugal pump employs centrifugal force to transfer other fluids through a revolving impeller.…

Q: A centrifugal pump operating at 1150 rpm showed a total head of 40 ft. at a capacity of 600 gpm. The…

Q: Analyze to select the type of the turbine when its diameter is 600 mm, rotational speed is 600 rpm…

A: Given: The diameter of wheel, D = 600 mm The rotational speed, N = 600 rpm The head of water, H =…

Q: For a single stage impulse turbine: Rotor diameter= 1 m Speed%3D 2500 rpm Nozzle angle= 20°…

A: GIVEN DATA- NOZZEL ANGLE =20' DIAMETER D=1m SPEED N=2500rpm

Q: While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at a head of 75 ft. If the…

A: Given data as per question Rotational speed =900 rpm head =75 ft Flow rate =2500 gpm = 5.57 ft3/s…

Q: ratio of external to internal diameter 2:1. Calculate (a) the hydraulic efficiency, (2) power, and…

A: Given: Q=1500 l/s H=6.2 m D2/D1=2 D2=1.2 m N=210 rpm A=0.65 m^2 To determine: (a) the hydraulic…

Q: Q.2. A catrifugal pump is operating at the rotation rate of 750 rpm. Water leaves the blade at 40°…

A: As per given question we have determine the a) Draw the velocity triangles at inlet and outlet of…

Q: The effective head across the turbine is 160 m and the speed required for electrical generation is…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Q: Dimension of a centrifugal pump impeller are Parameter Inlet, Section 1 Outlet, Section 2 Radius,r…

Q: A jet discharges from 35mm diameter orifice in a vertical plane under a head of 4m. The center of…

A: Diameter d = 35mm = 0.035m head H = 4m Center height from ground, h = 1.2m coefficient of velocity…

Q: b) The following data refers to an axial flow turbines. Stream speed at the exit blade = 150 m/s,…

Q: Q6: Calculate the specific speed for the centrifugal pump operates at (3000 r.p.m) & head of (6m)…

A: Given data N = 3000 r.p.m head (H) = 6 m discharge (Q) = 0.2 m3/s To determine specific speed…

Q: 1. A Pelton wheel of 4 m diameter operates with a head of 1000 m. Estimate the flow rate and power…

A: Solution Calculate the flow rate v=2gh=2×9.81×1000=140 msQ=Av=π4×42×140=1759 m3s

Q: -A Francis turbine has a wheel diameter of 1.2 m at the entrance and 0.6 m at the exit. The blade…

A: Introduction: The Francis turbine is a hybrid of an impulse and reaction turbine, with the blades…

Q: find a and b. A jet of water of diameter 50 mm, having a velocity of 30 m/s strikes a curved vane…

A: given diameter of water jet d=50mmvelocity, V=30m/scurved vane which is moving with a velocity,…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Q1):
Impulse turbine diameter = 3.2m
O1 = O2
Angular velocity = 25 rad/s
Absolute velocities V1 = 140m/s and
V2 = 110m/s
Power developed by the wheel = 300kw
Calculate:
Jet
25mmd
VI
V:
1. the blade velocity.
2. the force exerted and
3. the angle O.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
It is desired to develop a 5 MW turbine under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head.(b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
The mean radius of an axial flow reaction turbine is 2.6 ft. and the axial velocityis 25 ft./s. The wicket gates are turned at an angle such that relative velocity at theinlet flow makes an angle of -45° with the blade velocity. The wheel and hub radiiare 3.6 ft. and 1.6 ft., respectively. The turbine rotates at 240 rpm. If water leaves theblade in a purely axial direction, calculate H and all relevant angles.Ans: H=81.87 ft.; α1=31.8°; β2=20.93°
It is desired to construct a hydraulic turbine for a hydraulic power plant to operate under the following conditions: discharge Q = 3.5 m3/s of water, the available net head = 290 meters, the hydraulic efficiency = 0.8, the rotating speed = 300 rpm. A Pelton wheel impulse turbine was selected with the following specifications: the bucket angle b2 = 160°, the coefficient of velocity for the nozzle is 0.98 and assume the friction coefficient k = 0.2. Determine the following:Jet Diameter to Wheel diameter ratio, dj/Dw. The Specific Speed in M.K.S., Ns.The computed head coefficient ϕ.The brake horsepower. The required number of Jets. The Pelton wheel diameter in meters.
[5] A Francis turbine operates at its maximum efficiency point at h0 = 0.94, corresponding to a power specific speed of 0.9 rad. The effective head across the turbine is 160 m and the speed required for electrical generation is 750 rev/min. The runner tip speed is 0.7 times the spouting velocity, the absolute flow angle at runner entry is 70 deg from the radial direction and the absolute flow at runner exit is without swirl. Assuming there are no losses in the guide vanes and the mechanical efficiency is 100%, determine (i) the turbine power and the volume flow rate; (ii) the runner diameter; (iii) the magnitude of the tangential component of the absolute velocity at runner inlet; (iv) the axial length of the runner vanes at inlet.
A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400 m. The nozzle diameter is 160 mm and the coefficient of velocity is 0.98, The diameter of the wheel bucket circle is 1.75 m and the buckets deflect the jet by 150°. The wheel-to-jet speed ratio is 0.45. Neglecting riction, calculate (1) the power developed by the turbine, (i) its speed and (i) hydraulic efficiency.
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. (a)At what speed, in RPM, should the turbine run under a head of 11 meters? (b)What horsepower would be developed?
Q-- Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Provide clear and complete solution as well as diagram. The initial condition of air in an air compressor is 97 kPa and 27 oC and discharges air at 350 kPa. The bore and stroke are 250 mm and 280 mm, respectively with percent clearance of 6 percent running at 310 rpm. Find the volume of air at suction in m3/hr. A. 232.61 C. 156.34B. 289.16 D. 135.23
A two stage centrifugal pump is designed to discharge water at a total head of 70 m with an overallefficiency of 0.76. The pump runs at 2331.6 rpm. The actual head developed (per stage) is 65% ofthe theoretical head. The flow at the inlet is pure radial. The impeller at the exit has a diameter of D2=0.219m and a width b2=0.0216m .The outlet blade angle is ?= 28°. Determine:1. The flow rate of the pump.2. The output power of the two stage centrifugal pump. Take ρ= 1000kg/m^3g=9.81 m^2/s
A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume that the speed ratio is 2.09 and the flow ratio is 0.68, and the overall efficiency is 60%. The diameter of the boss is 1/3 rd of the diameter of the runner . The diameter of the runner is *