Q1 of 2) The circuit given has reached steady state before the switch closes at time t = 0. (a) Determine the values of i(t), vc(t), and VR(t) immediately before the switch closes. Box answers. [6] (b) Determine the value of vr(t) immediately after the switch closes. [Note: inductor and capacitor not at steady state immediately after switch closes. Use: vc (0)= vc (0+) and i, (0¯)= i₁(0¹)] Show all work. Box Answers. [4] 30 92 35 V 2 μF vc (1) 0.125 H (1) 40 92 UR(1) yo t=0 40 Ω

Q1 of 2) The circuit given has reached steady state before the switch closes at time t = 0. (a) Determine the values of i(t), vc(t), and VR(t) immediately before the switch closes. Box answers. [6] (b) Determine the value of vr(t) immediately after the switch closes. [Note: inductor and capacitor not at steady state immediately after switch closes. Use: vc (0)= vc (0+) and i, (0¯)= i₁(0¹)] Show all work. Box Answers. [4] 30 92 35 V 2 μF vc (1) 0.125 H (1) 40 92 UR(1) yo t=0 40 Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

As displayed in attachment figure and LC circuit can be modeled by the following system of differential equations as attachment. Where L = inductance (H), t = time (s), i = current (A), and C = capacitance (F). Assuming that a solution is of the form = Ij sin (wt), determine the eigenvalues and eigenvectors for this system using Faddeev-Leverrier Method and Power Method with L = 1 H and C = 0.25 C. Draw the network, illustrating how the currents oscillate in their primary nodes. Assume initial value for power method.
What is the differential equation governing the growth of current in the circuit as a function of time after t=0? Express in terms of dI(t)/dt, I(t), Vb, R, and L Solve the differential equation obtained in Part A for the current I(t) as a function of time after the switch is closed at t=0. Express in terms of Vb, R, and L. Use the notation exp(x) for ex
The following equation is linear, constant-coefficient, homogeneous ordinary differential equation. my′′(t) + Ks y(t) = mg + 30Ks Select one: True False
The mathematical models of some continuous time systems are given above. x(t) is the input signal of the system, and y(t) is the output signal of the system. Which of the following systems is linear and which is nonlinear? For linear systems, write "linear" in the space next to the option. For non-linear systems, write "non-linear" in the space next to the option.
The initial values of i1 and i2 in the circuit shown are + 3 A and −5 A, respectively. The voltage at the terminals of the parallel inductors for t≥0 is −30e−5t mV. 1. a) If the parallel inductors are replaced by a single inductor, what is its inductance? 2. b) Find the initial current and its reference direction in the equivalent inductor. 3. c) Use the equivalent inductor to find i(t). 4. d) Find i1(t) and i2(t). Verify that the solutions for i1(t), i2(t), and i(t) satisfy Kirchhoff’s current law
A) Reduce the block diagram. B) G1(s)= 2/s, G2(s)= 1/4s+2, G3(s)=4, H(s)=0.5 according to the given values, find the system's time constant, natural frequency, and damping rate, and explain what dynamic behavior it will exhibit accordingly. C) G1(s)= 2/s, G2(s)= 1/4s+2, G3(s)=4, H(s)=0.5 Find the poles and zeros of the system according to the given values. Accordingly, specify whether the system is stable. Find the unit digit response (reverse laplace)
The circuit shown below is an underdamped system, and the current through the inductor has the form iL(t)=e^at ( ) (K1sinwt + K2coswt ) for t≥0 a. Determine the numerical values, including signs, of a and w b. If the initial conditions are iL(0) = 1A and Vc (0) =12V , determine the numerical values, including signs, of K1 and K2 c. Using the numbers determined above, write out the complete expression for iL(t)
Consider the circuit given below, where V = 120 V, R = 2.4 kΩ, and L = 60 mH. What is the time constant of the circuit with S1 closed? What is the time constant of the circuit with S1 closed? What is the eventual steady-state current with S1 closed? What is the value of the circuit current at the first instant (t = 0 s) S1 is closed? What is the value of the circuit current exactly one time constant after S1 is closed? How long after S1 is closed will it take before the circuit current reaches its steady-state value?
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0 and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the current as a function of time.
For the circuit below with the switch closed and then opening at t=0, and R1= 3Ω, R2= 7Ω, C = 0.2H, ig = 8A, vs = 2v, calculate the initial condition. Develop the differential equation for the solution for t > 0. Calculate the current ia(t) for all times.
It is known that the switch shown, T, is initially open and then it closed in theinstant t = 0. If it is assumed that the circuit has reached the stable state before the action of said switch:1.1. Determine the value of the capacitance of capacitor C so that the given circuit is critically damped.1.2. For the damping conditions of the previous part, find the expression for the current, i (t), forall t> 0.
Can you please help with this question? The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).