Q1) On a 2.7-cm-outer-diameter circular tube, a 1.5-mm-thick aluminum fin is placed. The fin measures 6 mm in length. The tube wall temperature is kept at 150°C, the ambient temperature at 15°C, and the convection heat-transfer coefficient is 20W/m² °C. Calculate how much heat is lost through the fin.

Q1) On a 2.7-cm-outer-diameter circular tube, a 1.5-mm-thick aluminum fin is placed. The fin measures 6 mm in length. The tube wall temperature is kept at 150°C, the ambient temperature at 15°C, and the convection heat-transfer coefficient is 20W/m² °C. Calculate how much heat is lost through the fin.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.10P: 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the...

See similar textbooks

Similar questions

3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
/ Hot square plate (1 m ×1 m) is to be cooled by attaching aluminum circular pin fins (D=0.25 cm, L= 3 cm) distributed with distance 0.6 cm as illustrated in Figs.(1-a) & (1-b). If the fin base temperature is 100°C, cooling air temperature is 30°C and h= 35 W/m. °C. Determine the total rate of heat transfer from the finned plate and the effectiveness of the fins? Assume k= 237 W/m.°C and nr=tanh mL/ mL.
The cylinders that come out of the heat treatment furnace are cooled in a stagnant air environment in a horizontal position. The cylinders have a diameter of 100 mm and a length of 0.1 m. The temperature of the cylinders is 440 ° C and the ambient temperature is 20 ° C. Calculate the heat transfer from 10 cylinders to the environment. a) 3125 W b) 2350 W C) 1848 W d) 1354 W e) 2750 W
The 8-mm-thick bottom of a 220-mm-diameter pan may be made from aluminum (k = 240 W/m · K) or copper (k = 390 W/m · K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C. If heat is transferred from the stove to the pan at a rate of 600 W, what is the temperature of the surface in contact with the stove for each of the two materials?
A cylindrical tube with inner and outer radius are 10 mm and 20 mm respectively and the temperature of the inner surface is 300 C while for the outer surface is 100 C . If the rate of heat transfer per unite length is 3625.88 W/m , the tube conductivity is :
Water flows on the inside of a steel pipe with an ID of 2.5 cm. The wall thickness is 2 mm, and the convection coefficient on the inside is 500 W/m2◦C. The convection coefficient on the outside is 12 W/m2 ◦C. Calculate the overall heat-transfer coefficient.
A 20 cm diameter pipe (? = 0.8) is placed in a brick duct (? = 0.9) made of square section with dimension of 30 cm. The temperature of the pipe is 200oC while the temperature of the brick duct is 20oC. Calculate the rate of heat transfer (W) between the pipe and the duct.