Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the rpm of the motor is 600. The diameter of the machine pulley C is 180 mm. The ratio of the tight- and slack- tensions on the belt is 3. Two bearings A and B support the shaft. The shaft made from carbon steel with SAE number 1040 cold rolled. Determine the shaft diameter if the torque applied is dynamically reversed and the bending moment is applied statically. The pulley and gear are mounted on shaft using keyways. Design these keys if the key material is the same of the shaft material. 300 Pá 579.28N P1591.55N 300 300

Q1/ The power transmitted by the motor to the main shaft as shown in figure (1) are 15 kW with the rpm of the motor is 600. The diameter of the machine pulley C is 180 mm. The ratio of the tight- and slack- tensions on the belt is 3. Two bearings A and B support the shaft. The shaft made from carbon steel with SAE number 1040 cold rolled. Determine the shaft diameter if the torque applied is dynamically reversed and the bending moment is applied statically. The pulley and gear are mounted on shaft using keyways. Design these keys if the key material is the same of the shaft material. 300 Pá 579.28N P1591.55N 300 300

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
A 10" in diameter helical gear carries a torque of 3,000 in-lb. It has 20 deg. Involute stub teeth and a helix angle of 30 deg. Determine: (a) the tangential component of the load on the teeth in the plane of rotation; (b) the separating component of the load on the teeth; (c) the angle of obliquity in th plane normal to the pitch element of the tooth, and (d) the resultant load on the tooth
1. A double square thread power screw has a pitch of 6 mm and mean radius of34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required toturn the screw.A. 343.74 N-m B. 353.47 N-m C. 335.47 N-m D. 347.35 N-m2. A lubricated bolt needs an initial torque of 145 lb-ft to take the initial tension brought by the compressor withoutbreaking. Determine the initial torque needed by the bolt if the bolt was not lubricated.A. 107.85 lb-ft B.108.25 lb-ft C. 108.75 lb-ft D. 193.33 lb-ft
Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm long. Oneis solid but the other is hollow with an inside diameter of 40 mm. Both are made from steel. Compare the torsionalshear stress, the angle of twist, and the mass of the two designs if they are subjected to a torque of 850 N ·m.
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
A 9/16 inch height x 3.5 inches length flat key is keyed to a 50.8 mm diameter shaft. Determine the torque developed in key if bearing stress allowable is 35 Ksi. Use factor of safety of 3.
Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it rotates with revolution of 67.6 RPS. Maximum torsional stress equivalent to 50000 kPa.
. Determine the angle of twist for the steel (AISI 4340, OQT 1200 F) hollow shaft with anoutside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kWof power at a speed of 45 rad/sec. The shaft length is 400 mm
Two concentric, helical compression springs support a 6.5-kip load. The larger spring has an outside diameter of 7 in., a free length of 7 1/8 in., 4 turns, and is made of a 1 3⁄8 in. steel wire. The smaller spring has an outside diameter of 4 1⁄8 in., a free length of 6 13/16 in., 6 turns, and is made of 7⁄8 in. steel wire. Compute the shearing stress in each spring. PLEASE I NEED IT . ASAP
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
The composite shaft below, consists of three sections, a tubular indication welded, through flanges Aand B, two 1” diameter bars. Neglect the thickness of the flanges and determine the angle of twist of the endC from shaft to end D. Shaft 0 is relative to a torque of lb × ft. The A-36 material.
A belted transmission system is loaded as shown in Figure. The input shaft takes its power from a 40 kW motor that runs at 1000 rpm. The output shaft drives a certain machinery equipment. Determine the following: a. torque available at each of shafts A, B, and C. b. torsional stress induced on the 60 mm diameter output shaft c. length of belt required to connect each pair of pulleys d. maximum bending moment on shaft B, considering a belt coefficient of friction of 0.30.