Q1/ The space between two large plane surfaces kept 2.5 cm apart is filled with liquid of viscosity 0.0825 kg/m.s. What force is required to drag a thin plate of surface area 0.005 cm² between the two large surfaces at speed of 0.5 m/s, (i) when the plate is placed in the middle of the two surfaces, and (ii) when the plate is placed 0.015 m from one of the plates surfaces.

Q1/ The space between two large plane surfaces kept 2.5 cm apart is filled with liquid of viscosity 0.0825 kg/m.s. What force is required to drag a thin plate of surface area 0.005 cm² between the two large surfaces at speed of 0.5 m/s, (i) when the plate is placed in the middle of the two surfaces, and (ii) when the plate is placed 0.015 m from one of the plates surfaces.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two large plane surfaces are 1 in apart, and the space between them is filled with a liquid of absolute viscosity 0.0200 lb-sec/ft2. Assuming the velocity gradient to be a straight line, what force is required to pull a very thin plate of 4.00 ft2 area at constant speed of 1.00 ft/sec if the plate is 1/3 in from one of the surfaces?
A 1.5 m diameter open vessel, 2m high is filled with oil s.g= 0.85 at a depth of 1.6m and rotated at 47 rpm. a. what is the resulting depth of liquid at the center of the vessel? b. what angular speed should be imposed on the vessel such that the liquid touches the bottom surface of the vessel at the center? c. What angular speed should be imposed on the vessel such that there is no liquid 0.47m from the v ertical axis of the vessel?
If a particle has initial velocity of v0 = 12 ft/s to the right, at s0 = 0, determine its position when t = 10 s, if a = 2 ft/s2 to the left.
Q3 The space between two square flat parallel plates is filled with oil . Each side of the plate is 720 mm . The thickness of the oil film is 15 mm . The upper plate , which moves at 3 m / s requires a force of 120 N to maintain the speed . Determine : ( 1 ) The dynamic viscosity of the oil ; ( ii ) The kinematic viscosity of oil if the specific gravity of oil is 0.95 .
Determine the distances x and y for equilibrium if F1 = 800 N and F2 = 1000 N.
The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
4. An open cylindrical tank 2 m in diameter and 4 m high contains water to a depth of 3 m. It is rotated about its own vertical axis with a constant angular speed. a. If w = 8 rad/s, how much water is spilled out and to what depth will the water stand when brought to rest?b.What angular speed w (in rpm) will just zero the depth of water at the center or the tank?c.If w = 100 rpm, how much area at the bottom of the tank is uncovered?
A 450-N is in contact with a level plane of fk = 0.10. The block is acted upon by a horizontal force of 75N. The block reaches a velocity of 15m/s, starting from rest. If the 75-N force is then removed, how much longer will the block continue to move?
A boy slides down a water chute starting from rest at A. Neglecting friction. a. which of the following gives the velocity at the end of the chute at B in ft/s. b. which of the following gives the velocity on entering the water at C in ft/s. C. which of the following gives the horizontal distance of C from B in miles.
The ball at A is hit with an angle of ƟA = 30 °. If the ball hits the ground at point B with coordinates x = (5) and y = (- 3): i) The speed at which the ball was hit; andii) Calculate the velocity at point B.
C.acceleration at beginning
Two large plane surfaces are in a part ,and the space between them is filled with a liquid of absolute viscosity 0.0200 lbsec/ft2. Assuming the velocity gradient to be a straight line , what froce is required to pull a very thin plate of 4.00ft2 area at a constant speed of 1.00ft/sec if the plate is 1/3 in from one of the surface ?