Q1 ]: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown in Fig. Q1. If the normal stress in each rod must be limited to 275 MN/m². (a) find the minimum diameter required for each rod. (b) if the L₁ = 115 mm and L2 = 105 mm, compute the total deformation of the rod, the modulus of elasticity E = 60 GN/m². 130 kN 65 kN A -d₁ 130 kN B

Q1 ]: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown in Fig. Q1. If the normal stress in each rod must be limited to 275 MN/m². (a) find the minimum diameter required for each rod. (b) if the L₁ = 115 mm and L2 = 105 mm, compute the total deformation of the rod, the modulus of elasticity E = 60 GN/m². 130 kN 65 kN A -d₁ 130 kN B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.2P: Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.

See similar textbooks

Similar questions

1. Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b = 0.12 m, depth, d = 0.05 m with an equal thickness on all sides, t = 0.003 m. Calculate the compressive stress σ in the tube. Give your answer in N/mm2 to 2 decimal places.
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: All three principle stresses, the max in plane shear stress, average normal stress and absolute max shear stress
Mechanics of Deformable Bodies. Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following: a. Calculate the tension of the cable. b. Determine the diameter of the wire if the allowable stress is 125 MPa. c. If the diameter of the cable is 10 mm, find the deflection of the steel cable. d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
At a point in a strained material, the intensities of normal stresses on two planes at right angles to each other are 35 N/mm2 and 20 N/ mm2 both tensile. They are accompanied by shear stress of 15 N/ mm2. Find the principal planes and principal stresses. Find also maximum shear stress.
A plane stress state is given by the principal stresses σx =25 MPa and σy= -11 MPa. Determine σx' in the case that the system is inclined by 30 degrees (counter-clockwise). Give your answer in MPa to the nearest whole number.
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12 ksi, Sy = 17 ksi, and Sxy = 18 ksi.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(c) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
The global stresses in a three-ply laminate are given at the top and bottom surface of each ply in the tables below. Assume that each ply is 0.005 in. thick and the laminate has a top cross section of 4 in. × 4 in. What is the resultant force component Nx for the laminate in lb/in? What is the resultant force component Ny for the laminate in lb/in? What is the resultant force component Nxy for the laminate in lb/in?