Electrical Engineering - Power System AnalysisPlease solve the question quicklyPlease im begging you help me very quickly ?? ?? ?? ?? ?? Q1. A transmission line of any length can be represented by the four-terminal network with ABCD constants asshown below:IstoABCDVRRedraw the below table by hand and fill in using parameters such as Z (impedance), Y (Admittance),Z (characteristic impedance) , y (propagation constant), L (TL Length).One example is given.Line LengthEquivalentCircuitSeriesACDShortImpedanceMediumNominal IINominal TLongDistributedCosh y L

Answered: Image /qna-images/answer/3f2c2566-520a-43e5-8360-1a1ed2bb53a2.jpg

Q1. A transmission line of any length can be represented by the four-terminal network with ABCD constants as shown below: Isto IR+ ABCD VR Redraw the below table by hand and fill in using parameters such as Z (impedance), Y (Admittance), Z. (characteristic impedance), y (propagation constant), L (TL Length). One example is given. Line Length Equivalent Circuit A C D Short Series Impedance Medium Nominal II Nominal T Long Distributed Cosh y L

Q1. A transmission line of any length can be represented by the four-terminal network with ABCD constants as shown below: Isto IR+ ABCD VR Redraw the below table by hand and fill in using parameters such as Z (impedance), Y (Admittance), Z. (characteristic impedance), y (propagation constant), L (TL Length). One example is given. Line Length Equivalent Circuit A C D Short Series Impedance Medium Nominal II Nominal T Long Distributed Cosh y L

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.51P

See similar textbooks

Similar questions

Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
Representing a transmission line by the two-port network, in terms of ABCD parameters, (a) express VS, which is the sending-end voltage, in terms of VR, which is the receiving-end voltage, and IR, the receiving-end current, and (b) express IS, which is the sending-end current, in terms of VR and IR. (a) VS= _________ (b) IS= ________
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
A 40-km, 220-kV, 60-Hz three-phase overhead transmission line has a per-phase resistanceof 0.15 W/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance.Using the short line model, find the ABCD parameters. The sending-end voltage, voltageregulation, sending-end power, and transmission line efficiency when the line is supplyinga three-phase load of: (a) 381 MVA at 0.8 power factor lagging and at 220 kV, (b) 381MVAat 0.8 power factor leading and at 220 kV. How does the load type (capacitive or inductive)affect the sending voltage magnitude, voltage regulation and efficiency?
b) Ghana Grid Company (GRIDCo) designed a short transmission line using the A, B, C, D line constant of a transmission line parameters in its analysis. The engineering planning department came up with the design and said that when they computed the line performance using the equation AD – BC the answer was equal to 1.As an employee at the Ministry of Energy (MoEn) having oversight responsibility over GRIDCo, how would you accept the answer and recommend the Government of Ghana (GoG) to go ahead to implement the short transmission line?
With the system shown in the figure, use 100MVA as system base, and 230 kV as base voltage along the transmission line. For the same system in the figure, build the Y-bus matrix without the Load. 1. What is the element Y11? Provide the susceptance value 2. What is the element Y22? Provide the susceptance value
Question 1. The impedance of a 150 km long transmission line is ? = 0.06 + ?0.48 ?/??, and the shunt admittance value is given as ? = ?3.33?10−6 ?/??. Under 250 kV voltage at the end of the line A power of 250 MW is drawn with a reverse power factor cos ? = 0.95. Nominal π equivalent using the circuit; a) Find the ABCD parameters. b) Find the voltage, current and power factor per line.
With the system shown in figures, use 100MVA as system base, and 230 kV as base voltage along the transmission line. 1. Based on the system diagram with buses labelled accordingly what should be the rank of the square Y-bus matrix? 2. Build the Y-bus matrix without the Load. What is the element Y11 in susceptance value? 3. Build the Y-bus matrix without the Load. What is the element Y22 in susceptance value? 4. Build the Y-bus matrix without the Load. What is the element Y12 in susceptance value? 5. If you are to convert the real power load to a shunt conductance, what is the value of the conductance in per unit?
A 50ohm transmission line powered by a 3GHz source and terminated with a load impedance ZL=25-j60 ohms will be matched with the shorted parallel side. What should be the length, in m, of the parallel lateral line calculated using the Smith diagram ?
A conventional nominal T transmission line is composed of the following: a lumped shunt (parallel) impedance of 92 ohms at the center of the line and a lumped sending and receiving series impedance of 496 ohms for both ends. In a two-port network analysis, determine the Z12 parameter of the circuit described.
A single circuit 60 Hz transmission line. the conductors are Linnet type with flat horizontal spacing of 17.46 feet between conductors. Determine: (a) Assume that the line is short with a length of 50 miles, calculate the parameters of the line and draw the equivalent circuit. (b) Assume that the line is average with length of 150 miles (Pi-nominal model). draw the pi-nominal circuit for the transmission line and calculate its parameters (Z and Y/2 values, where Z is the series impedance of the transmission line and Y is the shunt admittance).