Q1. An order for 5000 units of Part 491 is received by the Diamonds & Spades Engineering Company. The raw material used for the production of part costs $1.5 per part. The basic manufacturing sequence, with standard operation times per part and machine overhead rates, is given below: Operation Cutting Milling Drilling Grinding Packaging Time per Part 3 min. 5 min. 4 min. 3 min. 0.3 min. Overhead Rate $1.20/hour 2.00/hour 1.70/hour 1.40/hour The direct labor hour per part is equal to the machine time per part (packaging is a manual operation only). The tooling cost for this job order is estimated to be $500. In addition to the tooling costs and machine overhead costs, factory overhead costs are $15 per direct labor hour. The average direct labor hour rate is $10 per hour. a. Assuming zero scrap rate during production, determine the total estimated costs for the job order of 5000 units. b. Determine the unit selling price if profit is to be 25% of the selling price.

Q1. An order for 5000 units of Part 491 is received by the Diamonds & Spades Engineering Company. The raw material used for the production of part costs $1.5 per part. The basic manufacturing sequence, with standard operation times per part and machine overhead rates, is given below: Operation Cutting Milling Drilling Grinding Packaging Time per Part 3 min. 5 min. 4 min. 3 min. 0.3 min. Overhead Rate $1.20/hour 2.00/hour 1.70/hour 1.40/hour The direct labor hour per part is equal to the machine time per part (packaging is a manual operation only). The tooling cost for this job order is estimated to be $500. In addition to the tooling costs and machine overhead costs, factory overhead costs are $15 per direct labor hour. The average direct labor hour rate is $10 per hour. a. Assuming zero scrap rate during production, determine the total estimated costs for the job order of 5000 units. b. Determine the unit selling price if profit is to be 25% of the selling price.

Principles of Accounting Volume 2

19th Edition

ISBN:9781947172609

Author:OpenStax

Publisher:OpenStax

Chapter5: Process Costing

Section: Chapter Questions

Problem 1PB: The following product costs are available for Stellis Company on the production of erasers: direct...

See similar textbooks

Similar questions

Mello Manufacturing Company is a diversified manufacturer that manufactures three products (Alpha, Beta, and Omega) in a continuous production process. Senior management has asked the controller to conduct an activity-based costing study. The controller identified the amount of factory overhead required by the critical activities Activity-Based Product Costing of the organization as follows: Activity Cost Pool Activity $259,200 Production Setup 55,000 Materials handling 9,750 Inspection 60,000 Product engineering 123,200 Total $507,150 The activity bases identified for each activity are as follows: Activity Activity Base Production Machine hours Setup Number of setups Materials handling Number of parts Inspection Product engineering Number of inspection hours Number of engineering hours he activity-base usage quantities and units produced for the three products were determined from corporate records and are as follows: Number of Number of Previous Next
Concord Company manufactures two products, Mini A and Maxi B. Concord's overhead costs consist of setting up machines- $860000; machining- $2020000; and inspecting- $570000. Information on the two products is: Direct labour hours Machine setups Machine hours Inspections Mini A Maxi B $1324000. $1660400. $1690400. O $2542105. 10000 600 24000 800 28000 400 26000 700 Overhead applied to Maxi B using activity-based costing is
Sensor Systems manufactures an optical switch that it uses in its final product. The switch has the following manufacturing costs per unit: LOADING... (Click the icon to view the costs.) Direct materials $7.00 Direct labor 2.00 Variable overhead 8.00 Fixed overhead 6.50____________________________ Manufacturing product cost $23.50__________________________ _________________________________ LOADING... (Click the icon to view additional information.) Another company has offered to sell Sensor Systems the switch for $19.00 per unit. If Sensor Systems buys the switch from the outside supplier, the idle manufacturing facilities cannot be used for any other purpose, yet none of the fixed costs are avoidable. Prepare an outsourcing analysis to determine whether Sensor Systems should make or buy the switch. (For the Difference column, use a minus sign or parentheses only when the cost of outsourcing…
Use the following information for Exercises 5-44 through 5-46: The following six situations at Diviney Manufacturing Inc. are independent. a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of machine time and 7.5 pounds of material. The cost per labor hour is 12, the cost per machine hour is 8, and the cost per pound of materials is 10. b. With its original design, a gear requires 8 hours of setup time. By redesigning the gear so that the number of different grooves needed is reduced by 50%, the setup time is reduced by 75%. The cost per setup hour is 50. c. A product currently requires 6 moves. By redesigning the manufacturing layout, the number of moves can be reduced from 6 to 0. The cost per move is 20. d. Inspection time for a plant is 16,000 hours per year. The cost of inspection consists of salaries of 8 inspectors, totaling 320,000. Inspection also uses supplies costing 5 per inspection hour. The company eliminated most defective components by eliminating low-quality suppliers. The number of production errors was reduced dramatically by installing a system of statistical process control. Further quality improvements were realized by redesigning the products, making them easier to manufacture. The net effect was to achieve a close to zero-defect state and eliminate the need for any inspection activity. e. Each unit of a product requires 6 components. The average number of components is 6.5 due to component failure, requiring rework and extra components. Developing relations with the right suppliers and increasing the quality of the purchased component can reduce the average number of components to 6 components per unit. The cost per component is 500. f. A plant produces 100 different electronic products. Each product requires an average of 8 components that are purchased externally. The components are different for each part. By redesigning the products, it is possible to produce the 100 products so that they all have 4 components in common. This will reduce the demand for purchasing, receiving, and paying bills. Estimated savings from the reduced demand are 900,000 per year. 5-45 Driver Analysis Refer to the information for Diviney Manufacturing on the previous page. Required: CONCEPTUAL CONNECTION For each situation, identify the possible root cause(s) of the activity cost (such as plant layout, process design, and product design).
Cozy, Inc., manufactures small and large blankets. It estimates $350,000 in overhead during the manufacturing of 75,000 small blankets and 25,000 large blankets. What is the predetermined overhead rate if a small blanket takes 1 machine hour and a large blanket takes 2 machine hours?
Crystal Pools estimates overhead will utilize 250,000 machine hours and cost $750,000. It takes 2 machine hours per unit, direct material cost of $14 per unit, and direct labor of $20 per unit. What is the cost of each unit produced?
Use the following information for Exercises 5-44 through 5-46: The following six situations at Diviney Manufacturing Inc. are independent. a. A manual insertion process takes 30 minutes and 8 pounds of material to produce a product. Automating the insertion process requires 15 minutes of machine time and 7.5 pounds of material. The cost per labor hour is 12, the cost per machine hour is 8, and the cost per pound of materials is 10. b. With its original design, a gear requires 8 hours of setup time. By redesigning the gear so that the number of different grooves needed is reduced by 50%, the setup time is reduced by 75%. The cost per setup hour is 50. c. A product currently requires 6 moves. By redesigning the manufacturing layout, the number of moves can be reduced from 6 to 0. The cost per move is 20. d. Inspection time for a plant is 16,000 hours per year. The cost of inspection consists of salaries of 8 inspectors, totaling 320,000. Inspection also uses supplies costing 5 per inspection hour. The company eliminated most defective components by eliminating low-quality suppliers. The number of production errors was reduced dramatically by installing a system of statistical process control. Further quality improvements were realized by redesigning the products, making them easier to manufacture. The net effect was to achieve a close to zero-defect state and eliminate the need for any inspection activity. e. Each unit of a product requires 6 components. The average number of components is 6.5 due to component failure, requiring rework and extra components. Developing relations with the right suppliers and increasing the quality of the purchased component can reduce the average number of components to 6 components per unit. The cost per component is 500. f. A plant produces 100 different electronic products. Each product requires an average of 8 components that are purchased externally. The components are different for each part. By redesigning the products, it is possible to produce the 100 products so that they all have 4 components in common. This will reduce the demand for purchasing, receiving, and paying bills. Estimated savings from the reduced demand are 900,000 per year. 5-44 Nonvalue-Added Costs Refer to the information for Diviney Manufacturing on the previous page. Required: Estimate the nonvalue-added cost for each situation.
Steeler Towel Company estimates its overhead to be $250,000. It expects to have 100,000 direct labor hours costing $2,500,000 in labor and utilizing 12,500 machine hours. Calculate the predetermined overhead rate using: A. Direct labor hours B. Direct labor dollars C. Machine hours
The following product costs are available for Stellis Company on the production of erasers: direct materials, $22,000; direct labor, $35,000; manufacturing overhead, $17,500; selling expenses, $17,600; and administrative expenses; $13,400. What are the prime costs? What are the conversion costs? What is the total product cost? What is the total period cost? If 13,750 equivalent units are produced, what is the equivalent material cost per unit? If 17,500 equivalent units are produced, what is the equivalent conversion cost per unit?
Wrappers Tape makes two products: Simple and Removable. It estimates it will produce 369,991 units of Simple and 146,100 of Removable, and the overhead for each of its cost pools is as follows: It has also estimated the activities for each cost driver as follows: Â How much is the overhead allocated to each unit of Simple and Removable?
Boarders estimates overhead will utilize 160,000 machine hours and cost $80,000. It takes 4 machine hours per unit, direct material cost of $5 per unit, and direct labor of $5 per unit. What is the cost of each unit produced?
Plata Company has identified the following overhead activities, costs, and activity drivers for the coming year: Plata produces two models of microwave ovens with the following activity demands: The companys normal activity is 21,000 machine hours. Calculate the total overhead cost that would be assigned to Model X using an activity-based costing system: a. 230,000 b. 240,000 c. 280,000 d. 190,000