Q1. The cantilever beam shown in Fig.1 has an end of mass = 10 kg. The response of the system is x₁ = 0.5 m, x₂ = 0.25 m and damping time = 3 sec. Find out the equivalent stiffness and damping of the beam. (Note: Assume that the beam is massless). А 32 m 8 Fig.1: Cantilever beam.

Q1. The cantilever beam shown in Fig.1 has an end of mass = 10 kg. The response of the system is x₁ = 0.5 m, x₂ = 0.25 m and damping time = 3 sec. Find out the equivalent stiffness and damping of the beam. (Note: Assume that the beam is massless). А 32 m 8 Fig.1: Cantilever beam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A washing machine with a mass of 60 kg and a drum radius of 15 cm, rotates at 1000 rpm and washes 3 kg of unbalanced laundry. a) How much dynamic force would be transmitted to the ground if no vibration isolation was taken from the machine?b) What would be the stiffness (k) of the visco-elastic floor if an insulation measure with a damping ratio of 0.1 was taken, which would reduce the force transmitted to the floor by 90%?
Between a solid mass of 10 kg and floor, two slab of isolator, natural rubber and feltare kept in series as shown in Figure Q1(b). The natural rubber slab has a stiffnessof 3000 N/m and an equivalent viscous damping coefficient of 110 Ns/m. The feltslab has a stiffness of 12,200 N/m and an equivalent viscous damping coefficient of170 Ns/m. (i) Sketch the single degree of freedom spring-mass-damper system(ii) Determine the undamped and damped natural frequencies of the system inthe vertical direction. Neglect the mass of the isolator
Figure 1 shows a system comprising a bar with mass m-12 kg and the length of the bar L=2 m, two springs with stiffness kt=1000 N-m/rad and k = 2000 N/m, one damper with damping coefficient c=50 N-s/m and two additive masses at the end of the bar, where each mass (M) is equal to 50 kg. The rotation about the hinge A, measured with respect to the static equilibrium position of the system is 0 (t). The system is excited by force (F) so find the state space representation of the system if the output y=ġ(t).
sum - 1 : determine magnification factor of forced vibration produced by oscillator fixed at middle of the beam at a speed of 600 rpm. The weight concentrated at the middle of the beam is 5000 N and produces statically deflection of the beam equal to 0.025 cm. Neglect the weight of the beam and damping is proportional to velocity of 2.5 cm/sec and force = 500 N sum - 2 : An automobile whose weight is 150 N and it is mounted on 4 identical springs due to its weight it sags by 250 mm . each shock absorber has damping coefficient of 0.4 N for a velocity oof 30 mm/sec. The car is placed on a platform which moves vertically at resonance speed having an amplitude of 10mm. Find the amplitude of the car Sum - 3: A SDOF has undamped natural frequency of 7 rad/sec. and a damping factor of 10%. The initial conditions are x0 = 0 and V0 = 0.5 m/sec. Find damped frequency and equation of motion of the system Sum- 4; A SDOF system with a mass 25 kg and stiffness 10 N/mm with damping 0.15 Ns/m…
A spring-mass system with m = 0.5 kg and k = 10,000 N/m with negligible damping, is used as a vibration pickup. When mounted on a structure vibrating with an amplitude of 4 mm, the total displacement of the mass of the pickup is observed to be 12 mm. Find the frequency of the vibrating structure.
The force-deflection curve for a composite structure of mass, m = 2000 kg, is shown experimentally. a) Find the hysteresis damping ratio η, the logarithmic δ, and the equivalent damping coefficient Ceq. Need B,C,D b) Find the value of stiffness from the graph in N/mm. c) Assume initial condition of u0 = 1.5mm, v0 = 2mm/sec, determine the free vibration response of this structure. d) Plot the response from part c. Hints: k = 165 N/mm, U (part a) = 4.3mm, η = 0.344, Ceq = 6.25 N.sec/mm, α = 14.15°, U (part b) = 1.52mm.
A SDOF system with a mass 25 kg and stiffness 10 N/mm with damping 0.15 Ns/m is initially at rest. IF the inital velocity is 100 mm/sec. find the expression for subsequent displacement .Hence find displacement and velocity at t=2 secs
Mechanical Vibration Lesson A 65 kg industrial sewing machine has an imbalance value of 0.15 kgm in rotation. The machine operates at 125 Hz and is located on the ground with a spring coefficient of 2 x 106 N / m and a dimensionless damping coefficient of 0.12. Find the uniform regime amplitude of the machine.
A machine is represented as a single degree of freedom spring-mass-damper system. The machine has a total mass of (109)kg, an out-of-balance mass 0.125 kg, eccentricity of 0.01 m, coefficient of damping (109)N/ (m/sec), and spring stiffness (1009) N/m. The rotational speed of the machine is 3000 rpm. Determine the maximum amplitude of vibration due to out-of-balance. Suggest a method for the control of vibration caused due to out-of-balance.
A rotating machine of 400 kg is similar to the system shown below. It operates at 3600 rpm (note: 1 rpm = 2π/60 rad/s). The machine is unbalanced such that its effect is equivalent to a 4 kg mass located 20 cm from the axis of rotation. An isolator with a spring stiffness of 8x106 N/m and a damping constant of 2x104 Ns/m is placed between the machine and the foundation. Determine the steady state response of the system. Find the force transmitted to the foundation and transmissibility of the isolator. Find the damping ratio of the system ζ . Find the transmissibility of the system, Tf. Find the frequency ratio of the system, β. Find the amplitude of the harmonic excitation force of the system, Fo in Newton (N). Find the displacement amplitude of the steady state response of the system, X in millimeters (mm). Find the damped frequency of the system, ωd in rad/s. Find the force transmitted to the foundation, FT in Newton (N). Find the frequency of the harmonic…
A spring-mass-damper system has mass of 100 kg, stiffness of 3000 N/m and damping coefficient of 300 kg/s. Calculate the undamped natural frequency, the damping ratio and the damped natural frequency.
A vehicle weighing 5,000 lb is supported on four identical springs and four identical viscous dampers. The static deflection of the vehicle under its own weight is 10 in. Determine the damping required for each of the dampers so that the critical damping is achieved.